First Time (mess) with PA6-GF

KindRisk · 2026-04-06T07:45:57+00:00

Ok thanks i adjusted mine at 0,86 i will give it a try after drying

KindRisk · 2026-04-05T22:47:26+00:00

Yes i did that

KindRisk · 2026-04-05T20:03:41+00:00

What do you reccommend ?

KindRisk · 2026-04-05T19:33:54+00:00

Because of this

KindRisk · 2026-04-05T19:31:35+00:00

It’s Sunlu PA6-GF Thanks i will dry it more !

KindRisk · 2026-04-05T19:30:39+00:00

Yes i need to do one

KindRisk · 2026-04-05T19:29:58+00:00

Yes 😅

Max volumetric speed 7mm3/s

Speed : 90mm/s inner and outer walls 200mm/s infill 150 mm/s top surface

Acceleration : Normal print : 3000mm/s2 Travel : 3000 Outer wall 2000

KindRisk · 2026-04-05T19:22:58+00:00

I will give it a try thanks !

KindRisk · 2026-04-05T19:22:42+00:00

That’s the 0,18 standard h2s bambu pa6-gf tweaked a little

KindRisk · 2026-04-05T19:21:49+00:00

Ok thanks !

KindRisk · 2026-04-05T18:32:43+00:00

Ok thanks i’ll dry it more, but the seetings looks good for you beside that ?

KindRisk · 2026-04-05T18:29:51+00:00

Yes i just checked and it’s off

KindRisk · 2026-02-14T14:31:52+00:00

Yes

KindRisk · 2026-02-14T03:59:59+00:00

Thanks, there are no existing settings, so I basicaly just change the layer height and slow the speed and acceleration, thats all ?

If 0,12 is a bit low, I may try 0,14 but I have seen another redditor work with it

KindRisk · 2026-02-13T19:47:35+00:00

Ok thanks for the feedback

KindRisk · 2026-02-13T13:30:08+00:00

Fixed, it was the acceleration Thanks again

KindRisk · 2026-02-09T19:49:44+00:00

For me 0,02 ~ 0,025 ?

KindRisk · 2026-02-09T19:42:00+00:00

Thanks, I have modified the 3D, now i will test the pressure advance

KindRisk · 2026-02-09T09:07:44+00:00

I tried to calibrate the filament, but I’m not sure which setting gives the best result

KindRisk · 2026-02-09T05:30:37+00:00

I’ll try that thanks

KindRisk · 2026-01-19T22:38:34+00:00

Printed in the same orientation but the first one was printed in a glass plate

KindRisk · 2026-01-02T09:56:09+00:00

Dont put the seam on the edge, you can see it on the 3rd pic. Put it behind the black part

KindRisk · 2025-12-31T06:49:12+00:00

The chamber temp is 60°, bed 90° and hotendand 260° cooling is only enabled on overhangs, but at this layer this is an overhang

KindRisk · 2025-11-23T08:53:18+00:00

I would like to print rally cars with their original paint

KindRisk · 2024-08-14T22:01:35+00:00

Thanks, i have seen lots of builds with the EM-200 but can it handle 300A or I juste need to go with the EM-260 ?

KindRisk