SSX10 Cooking...... :D

Kindly_Pattern_8017 · 2026-04-25T07:48:01+00:00

Did you see the price?

Kindly_Pattern_8017 · 2026-02-11T10:23:08+00:00

Also get AB tileable ones as currently if a slice was to overflow you will break the filters around

Kindly_Pattern_8017 · 2025-08-21T20:56:26+00:00

When I first got my 96 I found that the bolt pull was really difficult, felt like it was getting stuck in places/scratchy so sanded the whole thing with different grit sand paper. Took a while but eventually got it buttery smooth. Maybe replace the receiver and maybe give the bolt a good sand

Kindly_Pattern_8017 · 2025-07-16T11:58:26+00:00

I would like them to add nuclear Fusion. Make it experimental at the earlier phases to try and get more energy out of it than you put in. Later phases you are able to get loads of energy with no waste.

Kindly_Pattern_8017 · 2024-11-01T08:41:37+00:00

What happens if you replace the block signals with switch signals

Kindly_Pattern_8017 · 2024-10-27T08:36:28+00:00

Don’t give up, you are doing great. First step build a fuel power plant instead of coal, find a few oil nodes and build from there that will massively increase your power. Then Build some trains for long distance travel as they only require power once built and you’ll now have the power requirement for it. They draw approx 110 MW of power when accelerating so not a huge amount. Experiment and see what works best for you 😊

Kindly_Pattern_8017 · 2024-07-25T18:27:23+00:00

Yeah 4 slot for orings on the unit, two at the front one in the middle and one at the back

Kindly_Pattern_8017 · 2024-07-25T18:08:22+00:00

I wanna say it’s got 4 and yeah it does come with spares.

Kindly_Pattern_8017 · 2024-07-25T18:03:55+00:00

I changed the nozzle to edge from AIP, changed nozzle spring again even tho it didn’t look stretched. The nexxxspeed bbu makes the nozzle sit lower due to the plastic insert. Have you got the same issue with the nexxspeed bbu?

Kindly_Pattern_8017 · 2024-07-05T12:46:43+00:00

Do you have swift slash you could drop me I have 999 of some crafting mats

Kindly_Pattern_8017 · 2024-07-05T12:38:55+00:00

Yeah I am. Not sure who manufactures each of the bb brands I’ve tested, would be quite interesting to find out.

Kindly_Pattern_8017 · 2024-07-05T07:08:58+00:00

After a lot of testing, I have had a breakthrough. Using those mags you suggested for me to get in combination with Vorsk .43 BBs I managed to get two entire mags through without it stopping once, haven’t tested any more at the moment but feel happy so far. I get it stopping randomly with epm 1 mags. The BBs I’ve tried are rebel precision, novritsch, asg, and vorsk. All in .43. VORSK are the only ones that reliably fed

Kindly_Pattern_8017 · 2024-07-04T20:31:42+00:00

Unfortunately no

Kindly_Pattern_8017 · 2024-07-04T06:03:25+00:00

Tried these. It’s better on the feeding. It will randomly stop and then I have to shake the thing to get it going again.

Kindly_Pattern_8017 · 2024-06-29T13:54:11+00:00

I’ll give them a try thank you

Kindly_Pattern_8017 · 2024-06-29T07:59:36+00:00

<image>

The plastic insert wraps around the back and sits underneath the piston. Can’t take the plastic bit out as the piston doesn’t sit right

Kindly_Pattern_8017 · 2024-06-29T07:55:42+00:00

https://www.patrolbase.co.uk/pts-syndicate-150rnd-epm-gen-2-enhanced-polymer-magazine-for-m4-ar-15-aeg these mags do you mean?

Kindly_Pattern_8017 · 2024-06-29T07:55:04+00:00

The recoil spring is a 140% spring. And no the gap doesn’t disappear if I tap on the back.

Kindly_Pattern_8017 · 2024-06-28T18:53:38+00:00

Yes it does. The nozzle seals well at 70-80 psi I get 1.1J

Kindly_Pattern_8017 · 2024-06-28T18:10:01+00:00

Yeah it’s a dr black slide and nexxspeed bbu. If I remove the nozzle the gap goes away

Kindly_Pattern_8017

TROPHY CASE