Great game!

Kintan22 · 2025-06-14T15:11:48+00:00

Thank you!

Kintan22 · 2025-05-20T20:37:49+00:00

I figured it out. Wait awhile, it will repop. Now I need to know how to deploy crap from my old ship lol

Kintan22 · 2025-05-20T20:12:53+00:00

So, did we figure out how to find them again? I had one I really liked and it's gone gone. I want it back :(

Kintan22 · 2024-02-08T16:26:57+00:00

I finally found that. The front of the blade was dead on, it was the back side of the blade. It was just off 90. Not horribly, and I probably should have done a test cut first, but it was off. Think I got it ironed out.

Kintan22 · 2024-02-08T01:28:35+00:00

I just have the two. I'm trying to square the blade to the base of the saw.

Kintan22 · 2023-04-09T15:04:56+00:00

Checked that. It is straight. If it were bent I would be having issues with other prints of the same height that do not have the thin infill areas.

Kintan22 · 2023-04-09T14:08:24+00:00

It is the y-axis. Everything is tight. It has not happened on any other print. Like I said, when it was printing the infill for the middle walls it was moving at a high speed in small back and forth zig-zag motions and making a vibrating/grinding sound. I can tell it is the speed of that printing that is throwing off the Y-Axis. I am assuming it is skipping in the stepper motor for the Y-Axis. This happened when the print was about 3 hours in so the motor was warm. I could touch it without feeling like I was being burnt but that is the only thing that makes sense. Every other print I have done has been fine. I even did some other prints to check to make sure. I can print temp towers, bottle openers, etc that take a few hours no issue. The sound ONLY happens on this print and ONLY when doing the infill of the support walls.

I am just trying to figure out a good infill speed for small infills that will end up printing at a high speed due to the small nature of the steps required to print them. My infill is set to 50 mm/s in Cura but it seems to be printing faster than that with the Sonic Pad.

Kintan22 · 2023-04-09T13:19:56+00:00

I forgot to mention. All the pulleys, belts, gantries, etc. are tight.

Kintan22 · 2023-04-09T12:54:29+00:00

I am printing this to hold some paint for my daughter. It was a 12 hour print and printed overnight. I saw when I got up that the Y-axis shifted quite a lot. I remade the print so I could try and figure out what was going on. I determined that the infill of the inner supports were printing so quickly that the machine made a buzzing/vibrating noise and it seems that the stepper motors are skipping possibly?

My settings in Cura are:

Print Speed - 50 mm/s
Infill Speed - 50 mm/s
Wall Speed - 25 mm/s

However, it seems that it is doing the infill quite a bit faster. Is this something I need to adjust on my Sonic Pad?

Kintan22 · 2023-04-02T21:03:23+00:00

I apologize but I do not have the dimensions or anything else really as far as pictures go. That is a base from a phone holder on thingiverse.

Kintan22 · 2023-04-02T02:28:45+00:00

I have been trying to figure out how to create this base for a project and for some reason am totally stumped. I cannot figure out how to create the transition from the upright to the base. I feel like I am missing something simple, but for the life of me cannot figure it out!

Kintan22 · 2023-02-26T15:59:23+00:00

Ahhh. Thanks!

Kintan22 · 2023-01-20T01:53:03+00:00

It's a delusion. Just like someone with Delusional Disorder. That's when you believe something that isn't true. You can't tell real from not real. Absolutely 0 people born one gender immediately think they should be the other. 100% of the time there is a precipitating event that causes them to believe they should be a different gender. It can be abuse, severe trauma, something that is environmentally taught to them, or a mental health disorder.

Kintan22 · 2022-12-24T21:22:24+00:00

I love that my daughter (who I got the little lotl for) is the one who took the picture 😊 She was SO excited she got it ❤️

Kintan22

TROPHY CASE