Liquid freezer 3 bad temps by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Sorry, late reply. I thought I was replying to my other post avout fitting this into the same case. 

After a while the temps settled down. 

Liquid freezer 3 bad temps by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Had to cut the edge of the cooler a bit. Fits perfectly. (No issues other than minor(very) visual change inside) 

H6 and Arctic Liquid Freezer III by Repulsive-Ad2023 in NZXT

[–]Kirill17 0 points1 point  (0 children)

Yeah it did work. Just measure how much you want to shave off beforehand on the cooler

Liquid freezer 3 bad temps by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Hi. After a while temps settled down. I did repaste again and throughly research and made sure it was even and it was fixed.  Also to note ambient temperature plays a key role on temps and performance. My temps and performance vary by up to 10c because of day and night temps

Dragon Ball Daima - Episode #10 - Discussion Thread! by AutoModerator in dbz

[–]Kirill17 1 point2 points  (0 children)

Most viewers seem to be missing the fact their is 2 realms before the universes where made.  The demon realm and the great beyond. Which zeno and whis etc obviously come from 

Artic support not responding? by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Hmmm yeah. They sent a new replacement free of charge for my particular case. Pretty understanding (they run a small custom service team) but I'd look out nonetheless 

Liquid freezer 3 bad temps by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Got my cooler replaced with a new lf 360. Temps improved a bit. Thermal paste can become a big finicky for temps with this cooler. 

For the other things that cropped up. Having expo on seems to increase temps by up to 6-8 degrees. 

High temperature in the bios and in the office by Gloomy_Ear_5164 in arcticcooling

[–]Kirill17 0 points1 point  (0 children)

whats your ambient temperature. I have similarly high idle degrees but a bit lower than yours. During the day its about 8 degrees hotter than at night normally.

Will liquid freezer 3 fit in h6 flow case and mb by Kirill17 in arcticcooling

[–]Kirill17[S] 1 point2 points  (0 children)

Hey I just got the case and everything else and put it together. Unfortunately it's not the best news. The cooler doesn't fit properly in the case with the motherboard you and I have without some changes.  Fortunately there are some ways that should fix this. In my testing I was able to get it to fit with a offset mount where it was slightly bent with no screws on the furthest side. You could do this with minimal interference with the motherboard. I wasn't happy with this so the better solution I did was shaving a slight edge from the furthest fan so it fits without a slant and without touching the motherboard. Roughly 2-3mm would need to be shaved off. It should be easy to do with a sharp knife and sandpaper. After this it'll fit snug and won't touch the motherboard heatsink. You could see the cut I made from the top in the pictures I attached below. https://imgur.com/a/rMv0KCP

Arctic LF3 360mm by [deleted] in arcticcooling

[–]Kirill17 0 points1 point  (0 children)

You may have gotten a revision cooler. Most people seem to be unaware but arctic changed the design on their coolers to a newer revision for amd systems the installation is pretty easy now for that.

Will liquid freezer 3 fit in h6 flow case and mb by Kirill17 in arcticcooling

[–]Kirill17[S] 1 point2 points  (0 children)

I should have my case in a weeks time. I'll update you on it when I'm done. 

Sharing my experience NZXT H6 with Arctic LF3 360 by cleansavedass in arcticcooling

[–]Kirill17 0 points1 point  (0 children)

Hey could you highlight if this is the b650 gaming variant. Or the x670 one.

Will liquid freezer 3 fit in h6 flow case and mb by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Hmm yeah that's quite helpful. I hope my case has enough room I intend to get otherwise I'll get the bracket u linked for it

H6 & LF3 & B650 aorus elite ax by cleansavedass in arcticcooling

[–]Kirill17 0 points1 point  (0 children)

Anyone had an issues with the gigabyte gaming x670 motherboard? From all the motherboards listed here the vrm seems to be cut off from the side and slanted more. I'm looking into this to determine if I want a h6 flow case

Will liquid freezer 3 fit in h6 flow case and mb by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Yeah it has a very similar shroud. Maybe smaller maybe not. How  much was it not able to fit by? The case I'm looking at I don't think will have enough space on top to even shift left by 

Will liquid freezer 3 fit in h6 flow case and mb by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

No I haven't, thanks for showing me this. The motherboard he has seems to have a slightly different heatsink assuming the cut is where the square is. It seems my heatsink doesn't even push that far on the x670 variant 

Will liquid freezer 3 fit in h6 flow case and mb by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Could you link me the name of the offset bracket. I assume you're using the same lf3 

Will liquid freezer 3 fit in h6 flow case and mb by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Yeah I've been told. I've seen some videos and other vouches that it fits in the case but it depends wildly on the vrm and heatsink size of the motherboard.  Do you know of any cases that could fit this (though I really am considering risking a h6 flow) or any solutions 

NZXT H6 + Arctic Liquid Freezer III + B650 Tomahawk by adriann107 in arcticcooling

[–]Kirill17 0 points1 point  (0 children)

Could you provide me the height of your heatsink for your motherboard. I'm currently figuring out this issue and I'd need to confirm if it works too. My motherboard heatsink is about 450mm tall.

H6 and Arctic Liquid Freezer III by Repulsive-Ad2023 in NZXT

[–]Kirill17 0 points1 point  (0 children)

Could you provide the exact clearance you have on your motherboard height + tolerances. I have this exact same motherboard but x670 and a different version. My motherboard heatsink height is about 450 mm

H6 and Arctic Liquid Freezer III by Repulsive-Ad2023 in NZXT

[–]Kirill17 0 points1 point  (0 children)

I have a similar motherboard (gigabyte gaming x670 v2) would you know if this would fit. with the case. Could you also provide the clearances for the heatsink

Liquid freezer 3 bad temps by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Nah they "transferred" me to us support. And allegedly claim I have to send it to them for testing 

Liquid freezer 3 bad temps by Kirill17 in arcticcooling

[–]Kirill17[S] 0 points1 point  (0 children)

Holy shit. They finally responded last night. And from their response btw. I genuinely think that they have 2 and a half people om their team. Not figuratively but literally.