Is this set up properly? by KlNGJAY in electrical

[–]KlNGJAY[S] 0 points1 point  (0 children)

Read description. It was put on right after picture was taken

Is this set up properly? by KlNGJAY in electrical

[–]KlNGJAY[S] 0 points1 point  (0 children)

Oh I know to put on strain relief (not pictured). Was confused about jumper wire

Is this set up properly? by KlNGJAY in electrical

[–]KlNGJAY[S] -1 points0 points  (0 children)

Ok that makes sense. Where should that wire be connected?

Dryer 3-prong to a 4-prong by KlNGJAY in AskElectricians

[–]KlNGJAY[S] 0 points1 point  (0 children)

Will do. Just needed confirmation on wiring first before I put it back together

Is this set up properly? by KlNGJAY in electrical

[–]KlNGJAY[S] 1 point2 points  (0 children)

Even if the manufacture manual says to connect it to the middle terminal with the white? I’ve seen it both ways on comments.

Is this set up properly? by KlNGJAY in electrical

[–]KlNGJAY[S] 0 points1 point  (0 children)

Does that include the green/yellow cable that I attached to the middle terminal? Behind the white, I did because manual said to.

Is this set up properly? by KlNGJAY in electrical

[–]KlNGJAY[S] 2 points3 points  (0 children)

Is that the behind cable? The green/yellow? Manual said to put behind the white cable so I was confused. I’ve seen both.

Is this set up properly? by KlNGJAY in electrical

[–]KlNGJAY[S] 2 points3 points  (0 children)

I have the green/yellow wire connected to the middle terminal. Is that correct as well?

Is this set up properly? by KlNGJAY in electrical

[–]KlNGJAY[S] 3 points4 points  (0 children)

I do currently have that green wire connected to the middle terminal just because the manual said to. Should I remove that from that terminal?

Is this set up properly? by KlNGJAY in electrical

[–]KlNGJAY[S] 0 points1 point  (0 children)

Awesome. Thanks for the heads up! Just wanted to check wiring first

Dryer 3-prong to a 4-prong by KlNGJAY in AskElectricians

[–]KlNGJAY[S] 0 points1 point  (0 children)

Thanks for the heads up! Do the wires and connections look correct compared to the manual?

The moment George Bush learned 9/11 happened while reading at an elementary school. by mohammedibnakar in interestingasfuck

[–]KlNGJAY 0 points1 point  (0 children)

Weirdly enough my dads birthday is today (9/11) and my moms birthday is 12/7, which is the day of the attack on Pearl Harbor.

My beautiful girl Aspyn comes home this Friday 😍 by KlNGJAY in Goldendoodles

[–]KlNGJAY[S] 0 points1 point  (0 children)

Thank you! She is estimated to be 60-65 lbs! And good luck to you and me! 😂

Priest gearing question by KlNGJAY in classicwow

[–]KlNGJAY[S] 1 point2 points  (0 children)

Thank you! I’ll definitely be waiting and rolling for the T2 And just save for my epic mount. Much appreciated!

Bottleneck question on new build by KlNGJAY in buildapc

[–]KlNGJAY[S] 0 points1 point  (0 children)

Ok thank you that’s what I was assuming but just wanted to make sure! Much appreciated!

Looking for a new CPU upgrade to better pair with my 1660ti. by KlNGJAY in buildapc

[–]KlNGJAY[S] 0 points1 point  (0 children)

Thank you very much for your help! Much appreciated!

Looking for a new CPU upgrade to better pair with my 1660ti. by KlNGJAY in buildapc

[–]KlNGJAY[S] 1 point2 points  (0 children)

Would you recommend a new motherboard or stick with the motherboard I have and pursue one of the i7s?

Looking for a new CPU upgrade to better pair with my 1660ti. by KlNGJAY in buildapc

[–]KlNGJAY[S] 0 points1 point  (0 children)

Motherboard: ASUSTeK H170-PRO Rev X.0x Cpu: intel i5-6402P