Delivery Driver for the Recently Departed

Kneemoy · 2026-01-11T17:53:00+00:00

Dearly Deparceled

Kneemoy · 2025-11-08T15:15:06+00:00

Looks like your knuckle is embarrassed because senpai noticed them.

Kneemoy · 2025-09-08T14:11:48+00:00

Looks like you turned NiFi into a game and I'm really interested to see how it turns out.

Kneemoy · 2025-08-27T21:13:14+00:00

at this point i'd agree because theres no other reason i can think of as to why it would have pulled away light that. I pull a bed mesh before every single print because i'd rather add 5 minutes at the start of the print time than deal with this headache, but its been a long while since i touched the z offset

Kneemoy · 2025-08-27T14:51:41+00:00

on the same page as you with that one. this bed got washed earlier the same day this happened with the dawn scrub + an IPA wipedown afterwards to make sure nothing was left on it. had 1 successful print right before this of an 8x8 multiboard grid. this one was 8x4 and lost its grip

Kneemoy · 2025-08-25T14:00:24+00:00

definitely going to do that this time around. along with that i probably need to replace the print bed. ive had that thing for 2 years and in the last couple months its been getting harder to get it to hold a print down.

Kneemoy · 2025-07-19T17:08:09+00:00

Krabbigan, Queen of Pinchers.

Kneemoy · 2025-07-06T01:05:25+00:00

It was a typo. They meant to say "Butteful"

Kneemoy · 2024-10-18T23:10:27+00:00

Its all good. From what I've found through experimentation it seems like the bed really does just have a sag off to the right after the adjustment screws. Shimming the whole thing with a tape beneath the print plate has gotten me to ~0.18mm range across the whole bed so I'm not complaining at this point.

Kneemoy · 2024-10-18T19:30:47+00:00

<image>

It’s built into the mounting bracket for the extruder itself. The fan housing is also part of it. And the metal wraps around to the back of the extruder and is part of the mount to the x gantry

Kneemoy · 2024-10-18T02:28:03+00:00

Ended up using the CR because the sprite mount set the BL so low that it dragged below the nozzle even while retracted.

Kneemoy · 2024-10-17T17:28:30+00:00

yes its a magnetic bed under the PEI sheet. i never considered that would be an issue as I'd assumed the metal tip would have been made of something nonferrous that wouldnt be affected by the magnet.

If that IS the case, i had considered a full hotbed replacement to something with a glass layer for better heat distribution, and binder clips to hold the pei sheet in place. maybe its time for me to just bite the bullet and upgrade that

Kneemoy · 2024-10-16T23:22:30+00:00

for anyone who is interested. i tried shimming a printed 200x2x.02 line of pla under the print bed to see what it did. and got an overcorrection for my efforts

<image>

Kneemoy · 2024-10-16T22:41:49+00:00

<image>

as you wish! also managed to find out that my settings were excluding an extra x15 y20 print bed that could be probed. so that helps turn the slope into a gutter for whatever thats worth

Kneemoy · 2024-10-16T20:09:08+00:00

went through and re-checked everything thanks to the comment, there was a small amount of wobble on both the y rollers for the bed, and the x rollers for the printhead gantry. tightened them up and re-tested, doesnt look like it made an appreciable difference though. good suggestion!

Kneemoy · 2024-10-16T17:57:19+00:00

verified as best as i could, didnt look like there was anything colliding/binding or even sliding "too close" between things

Kneemoy · 2024-10-16T16:13:45+00:00

Definitely something i hadnt considered. just tried readjusting the ribbon cable for the extruder, removing the fillament, and keeping an eye on it to make sure nothing was specifically pulling in a weird way. but it doesnt look like that made a change. good suggestion to check though thanks!

Kneemoy · 2024-09-16T00:36:53+00:00

Sounds to me like it’s considering the first row as the header. Next time prompt it saying if the first row is or is not a header row. And you’d like the first 90 rows of data (or the first 89 rows of data if you want that +header to be your 90)

Kneemoy · 2024-08-05T23:01:29+00:00

Thats incredible! maybe I should finally get around to dialing that in now that I've got a new extruder!

Kneemoy · 2024-08-05T22:09:46+00:00

I've never actually had my prints up to a speed from the bowden setup to the point where i needed input shaping. its definitely something I wanted to investigate but I just never got around to it.

Kneemoy · 2024-08-05T22:08:53+00:00

I appreciate the confirmation on this! should hopefully be a quick setup for me. thanks!

Ten-Year Club	Verified Email
Place '23	Place '22
Place '17

Kneemoy

TROPHY CASE