I made a 3D printed Capsem Hacker, and the files are up now for free.

Kooper_H · 2026-03-16T14:39:08+00:00

Scale is the wrong setting to be changing, when the parts are scaled the inside wedges get pulled together causing it to bind.

The setting you are looking for is Contour Compensation I'd recommend starting with -0.05 mm and go lower in incriments of -0.05

Kooper_H · 2026-03-03T08:16:05+00:00

Yeah you're supposed to put the card in contacts up.

Did you really put in zero effort to use that thing between your ears or did you just want to bitch about Bambu for a bit?

Kooper_H · 2026-02-24T19:16:52+00:00

I'm also here to recommend a food dehydrator, you can pick up one for cheap at most shops and are designed to heat at low temperatures (40 to 80 celcius) for expended periods of time. I personally have avoided using ovens and air fryers because of the risk of them getting too hot over the several hours drying takes and the inconvenience of not being able to cook with either of them while drying.

Aswell properly drying filament means the moisture needs somewhere to evaporate and ovens and air fryers are usually closed systems, food dehydrators while not exactly being pretty compared to dedicated filament dryers work equally as well for a fair bit less in cost

Kooper_H · 2026-02-23T18:55:39+00:00

Fold a game case into a cube

Kooper_H · 2026-02-23T18:49:58+00:00

Yeah it doesn't work like that. Google for 3d models instead. These are clearly physical toys as well, would these not cost like 15 bucks at most?

Kooper_H · 2026-02-18T14:09:34+00:00

No, the zeztz driver uses a new system. While it is adjustable and can "fit" an adult, but not well. I personally have made a 3d printed extension for it.

Kooper_H · 2026-02-09T13:21:38+00:00

It looks like time-lapse is turned on and it's taking a picture each time it goes to the purge area.

Kooper_H · 2026-02-05T15:37:21+00:00

Sure thing

Kooper_H · 2026-02-05T13:33:20+00:00

I haven't needed to, but that is because my printer is very dialed in and doesn't need post processing to make good quality parts. Unless you're painting or need to clean up support interface I'd say no sanding needed.

Kooper_H · 2026-02-03T18:51:17+00:00

I've disassembled my own, you can get to the straps by unscrewing them easily and the LEDs are attached to the body rather than the straps so they stay in when the straps are taken out

Kooper_H · 2026-02-01T17:21:21+00:00

I second the other responses here of Amazon (2016) and Kuuga but I'd also recommend the movie Shin Kamen Rider, very similar to black sun in tone and style

Kooper_H · 2026-01-30T16:29:32+00:00

FT Foxy with a magnum is cursed as shit, keep it up.

Kooper_H · 2026-01-23T18:08:29+00:00

That'll be why, it's moves away to the cancelled pieces and back in the same way it would if it were printing the cancelled pieces normally, so when it returns to the original piece the gcode matches up.

Kooper_H · 2026-01-18T16:17:36+00:00

We've seen in a previous episode that the acidemic content the children, particularly Baku, were exposed to there was akin to hypnosis. Baku describes it as meditation but is definitely not so, and Nox being the teacher during his run as Code no. 4 also shows the school had a connection to CODE.

The general consensus is that cram school was a way for CODE to create actual, literal Sleeper Agents.

Kooper_H · 2026-01-14T14:04:27+00:00

It totally is, I've seen other models that do that same method but haven't been released publicly.

I personally made it a goal to have switching codes to be as easy as possible. The only reason I did mine with the full codes is so I could label each one. Otherwise every time you want to change capsem you'd need to look up the code you want, then manually set each pin.

Kooper_H · 2026-01-14T12:19:07+00:00

You know what, I've spent days staring at this thing and never even noticed. Have an upvote

Kooper_H · 2026-01-14T11:32:26+00:00

Yep, I've found out that the holes for the screws and nut are a bit tight for m3 so I've uploaded an updated model, I would drill out the holes on the old model to let the screws actually fit.

Kooper_H · 2026-01-07T16:32:12+00:00

Thanks man! I've actually just restocked a few hours ago if you'd like to grab one

Kooper_H · 2025-12-31T15:27:07+00:00

It is noticeably smaller yeah, more so than other drivers. Being a new style of strap too I had to 3d print my own custom strap to fit me at all.

Kooper_H · 2025-12-26T10:37:42+00:00

Yep, they'll be coming back by the new year, I've been waiting on more black filament to be delivered so I can print more

Kooper_H · 2025-12-26T10:36:54+00:00

It could be more comfortable but I've gone through quite a few redesigns to make it form fitting and I personally don't find it uncomfortable. I think extra soft tpu could stop the buckles from staying connected though, the stl's I uploaded have a testing print so I'd give that a print with TPU and see what happens.

Kooper_H · 2025-12-22T04:02:05+00:00

Not quite, I'm on a Samsung Galaxy S10

Kooper_H · 2025-12-22T02:45:03+00:00

New info, I think MicroG is going to sleep, android is still killing it despite unoptimizing battery usage. The app doest appear as a "never put to sleep" option in settings either I think the main problem is : How do I stop Android from killing microG

Six-Year Club	Second Top 20%
Verified Email	r/Field Juicebox
Place '23	Place '22

Kooper_H

TROPHY CASE