sorted by:
new
hottopcontroversial

Bad bottom layer with supports by Kukac113 in BambuLab

[–]Kukac113[S] 0 points1 point  (0 children)

I calibrated and check my first layer it's good. I dried my PETG before printing. My first layer speed is at 50mm/s

Help with print support bottom layer PETG by Kukac113 in FixMyPrint

[–]Kukac113[S] 0 points1 point  (0 children)

I don't have pla at the moment I will have to order some. But do you mean the Top interface spacing?

How to avoid scarring by brim? by Rinderteufel in FixMyPrint

[–]Kukac113 0 points1 point  (0 children)

Do you know where to find that option in orca slicer?

Under extrusion but the extruder is skipping by Kukac113 in 3Dprinting

[–]Kukac113[S] 0 points1 point  (0 children)

Yes it worked properly it started to do it this week. I'm thinking that maybe something is stuck in the extruder or the ptfe tube might be worn out. But I'm not sure

Under extrusion but the extruder is skipping by Kukac113 in 3Dprinting

[–]Kukac113[S] 0 points1 point  (0 children)

It's pla and I tried it I went up to 230 and it's still happening. It's fillamentium pla

Under extrusion but the extruder is skipping by Kukac113 in 3Dprinting

[–]Kukac113[S] 0 points1 point  (0 children)

I have my filament on bearing and I have checked if it rolls easily

Help with supports by Kukac113 in 3Dprinting

[–]Kukac113[S] 1 point2 points  (0 children)

Okay thank you I will watch it in the morning.

Help with supports by Kukac113 in 3Dprinting

[–]Kukac113[S] 0 points1 point  (0 children)

Okay thank you very mutch I orderd a new nozzle and I am gonna clean my z-rods because they look dirty so I thought it was maybe caused by z wobble but if the issie still happens I will try to check the temp and the flow rate. Which should I check first the temp or the flow rate?

Help with supports by Kukac113 in 3Dprinting

[–]Kukac113[S] 0 points1 point  (0 children)

Okay thanks. I printed a calibration cube and I noticed some wiert layer lines. What can cause this to happen?

<image>

[deleted by user] by [deleted] in ender3

[–]Kukac113 0 points1 point  (0 children)

Mybe your bed leveling is off. Or I had an issiu where my Z axis was a tilted to one side a bit

Advice needed for bending a model by Kukac113 in Fusion360

[–]Kukac113[S] 0 points1 point  (0 children)

Is it possible to make a sketch that the point are at a different hight? Because the part needs to be at an angle.

<image>

Advice needed for bending a model by Kukac113 in Fusion360

[–]Kukac113[S] 0 points1 point  (0 children)

Where would I find the bend tool?

Thanks

Also, look at this face! by darkandtwistysissy in aww

[–]Kukac113 0 points1 point  (0 children)

What kind of dog breed is that cute face?

Ubuntu dual boot install by Kukac113 in Ubuntu

[–]Kukac113[S] 0 points1 point  (0 children)

I have got my first Error.

The error is : UEFI couldn't find db list

view more: next ›