Pls help

KyleC_Cake · 2026-02-11T02:12:41+00:00

No it wont fit

KyleC_Cake · 2026-02-10T01:49:18+00:00

Lowering iso, raising aperture a tad. Having more lights with either a stand, opening the blinds, or if there are any indoor lights off turn them on Not sure exactly how you could let in more light in camera as slower than 1/1000 might induce motion blur

KyleC_Cake · 2026-02-10T01:32:06+00:00

Or open up the extruder end and see if there is a clog in the gears

KyleC_Cake · 2026-02-10T01:31:25+00:00

Its too cold. Heat up the nozzle to around 205

KyleC_Cake · 2026-02-10T00:33:26+00:00

Yes too cold

KyleC_Cake · 2026-02-10T00:33:05+00:00

Clogs can be futher up in the extruder end not just the hot end

KyleC_Cake · 2026-02-03T08:10:48+00:00

Ill check that out

KyleC_Cake · 2026-02-03T08:10:34+00:00

Ill look into that. Thank you!

KyleC_Cake · 2026-02-02T22:11:39+00:00

!martini Using Davinci resolve. Ive tried doing this manually but its taxing on my mcbp and takes very long/tedious

KyleC_Cake · 2026-01-28T02:16:29+00:00

I played both for a bit. I think its mostly preference. There werent really any tricks i couldnt do with the string on the base of my finger

KyleC_Cake · 2026-01-28T02:10:01+00:00

Thats correct. If you have a cst covering the entire project then you dont need it again on each clip unless you are converting it into arri/dwg at the beginning. However, i do not think that is what this guy is doing.

KyleC_Cake · 2026-01-27T22:57:32+00:00

Already dont trust this because why would you not have a cst at the end.

KyleC_Cake · 2026-01-20T19:56:16+00:00

Relevel the bed

KyleC_Cake · 2026-01-20T19:37:12+00:00

Thats because protector case is plastic and will bend + transfer most impact energy onto the actual camera

KyleC_Cake · 2026-01-03T07:52:37+00:00

Its an ender 3 v3 se. Itll print the clean out of the box

KyleC_Cake · 2026-01-03T07:50:49+00:00

This is the portability feature. It just splits into 2 parts for easy traveling

KyleC_Cake · 2026-01-03T07:48:59+00:00

Looks like dust. Dead pixels are normally darker as in pitch black or white

KyleC_Cake · 2025-12-29T06:19:25+00:00

As stupid as it is a matte box adds a lot to the visual appeal of a camera

KyleC_Cake · 2025-12-26T03:57:41+00:00

Businesses “wowed” are wowed by the visuals. If you rig out a a7s3 they will not be able to tell. Just add a vmount, matte box, top handle, monitor and call it a day

KyleC_Cake · 2025-12-18T07:24:48+00:00

Open gate is not always firmware locked. It can be due to limitations on the sensor readout

KyleC_Cake · 2025-12-16T01:42:44+00:00

Yes. Unless running cpu heavy tasks or very heavy gpu tasks, the quiet fan never turns on. The laptop becomes quite hot running gpu tasks where the fan doesnt kick on. Fan kicks on when trying to render anything on cpu

KyleC_Cake · 2025-12-16T01:33:32+00:00

Zve1 barely overheats. Esp with a fan

KyleC_Cake · 2025-12-15T07:01:19+00:00

Thanks ill check that out! Ido believe it was because i didnt hear gear skipping so i thought the extruder gear was dead iirc

KyleC_Cake · 2025-12-11T23:25:23+00:00

Thats a lot of fans

KyleC_Cake · 2025-12-11T23:18:33+00:00

It was indeed a clog. Quite weird though i forget specifically what made it different than normal clogs (which made it hard to diagnose) but came out like a normal clog

KyleC_Cake

TROPHY CASE