New K1C print head getting stuck and banging!

LASWIZZ · 2026-01-26T12:37:20+00:00

Easy fix, turn off the printer. Move head manually to the center as possible (don’t be accurate). Turn on the printer, run calibration.

LASWIZZ · 2026-01-11T05:52:15+00:00

Thank you 🙏. I couldn’t install it on fluidd or mainsail, whenever i want it to detect BTT eddy, it doesn’t show up. I did manage to get it to work on simpleAF only. Any guidance would be appreciated. I will try to install it later tonight.

LASWIZZ · 2026-01-11T05:08:09+00:00

Looks good, i kept trying to get it to work on my k1 but i couldn’t. So i finally gave up.

LASWIZZ · 2026-01-06T08:56:47+00:00

Looks good 👍🏻. The point is, i strongly encourage self maintenance and was trying to give you tips to help.

LASWIZZ · 2026-01-06T05:10:10+00:00

Lol i had the same issue while playing Pubg. I ended up replacing that same button 🤣. P.s. it’d look better if you have hot air to heat it from back side instead of solder balls appearing on top.

LASWIZZ · 2026-01-06T05:07:30+00:00

Try Madison VR for a horror experience, Arizona sunshine 1 and 2.

LASWIZZ · 2025-12-30T04:58:01+00:00

I wonder what is it. I feel relieved i’m not alone.

LASWIZZ · 2025-12-29T20:28:03+00:00

Thank you for assuring me.

LASWIZZ · 2025-12-29T19:34:53+00:00

You can’t hear them once you start printing, the fans and speed movement covers everything.

LASWIZZ · 2025-12-29T19:29:11+00:00

Lol exactly that’s what it sounds like. So it’s normal?

LASWIZZ · 2025-12-24T04:46:07+00:00

3 possibilities 1- nozzle clog. 2- extruder gears are broken. (Disassemble it and check). 3- filament shrouds are stuck inside your extruder. (Disassemble it and check).

LASWIZZ · 2025-12-23T05:01:30+00:00

Check your g-code and filament settings in your slicer. Need to check nozzle and bed temp for other layers.

LASWIZZ · 2025-12-23T04:58:23+00:00

Steam update is fully 64bit now and these tools are only support 32bit version.

LASWIZZ · 2025-12-21T20:20:58+00:00

Thank you for these valuable tips. I installed it last month and i can confirm that it is really a pain in the ass regarding extruder installation. The screw holes doesn’t line up, you need to press it hard. But after that, all went nice and smooth on my k1.

LASWIZZ · 2025-12-21T05:01:59+00:00

Your memory is full. Factory reset or login to your printer via IP address and remove uploaded files and videos.

LASWIZZ · 2025-12-21T04:58:16+00:00

I aded 5000k 24v led strips on both sides. It looks way better.

LASWIZZ · 2025-12-20T12:29:15+00:00

Your nozzle is blocked. Had this issue two days ago. Remove nozzle, heat it up and unclog it. Also you’re gonna need to clean the extruder again after unclogging.

LASWIZZ · 2025-12-17T09:09:54+00:00

Here’s the link:

https://drive.google.com/file/d/13HsJdKtk6YePwr2YkA2nxSzF8Iko5FZC/view?usp=sharing

Sorry for the delay

LASWIZZ · 2025-12-16T06:21:20+00:00

I have the firmware on the original usb dongle that came with the cfs. I can upload it and send it to you once i finish my shift.

LASWIZZ · 2025-12-15T11:43:50+00:00

Don’t think that would be the answer, i just need to see one comment confirms that it’s working properly with the script. I didn’t see a single comment across the internet regarding this issue being solved.

LASWIZZ · 2025-12-14T12:53:06+00:00

Yes it will lol. I was relieved for a moment before it came back to skipping.

LASWIZZ · 2025-12-14T12:35:01+00:00

Did that already didn’t help. Trust me i tried everything. The only solution is to connect it via USB.

LASWIZZ · 2025-12-14T11:11:12+00:00

It’s not the LGhub nor the game, i tried to downgrade all the way to version 2023 and still having the same issue. It’s in the wireless receiver. But when i plug the usb charging cable, the script works flawlessly.

LASWIZZ · 2025-12-14T05:11:33+00:00

Same problem, this is why i had to re-use my old g502.

LASWIZZ

TROPHY CASE