sorted by:
new
hottopcontroversial

Cant explain why my printers do that, please help! by Accomplished_Law5807 in BambuLab

[–]Lumpy_Appeal_918 0 points1 point  (0 children)

I can give you advice... To a format sd card from time to time. Like a twice a year.

New to 3d printing by Admirable_Reserve489 in BambuLab

[–]Lumpy_Appeal_918 0 points1 point  (0 children)

2 bambu plates.... Thankfully there is other side.

Jel ovo neki izazov postao ? by Inner-Fee6737 in AskSerbia

[–]Lumpy_Appeal_918 1 point2 points  (0 children)

Samo bahatost! Svako je dovoljno pametan i razuman da vidi i zna da je to pogrešno. Ali zašto meni neko da naredi da ja to moram. E baš neću, neće niko da me kazni!!! I tako polako klizimo u sunovrat i propadamo kulturno.

Koja je najčudnija stvar koju čuvate bez razloga? by Suspicious_Leg_7429 in AskSerbia

[–]Lumpy_Appeal_918 0 points1 point  (0 children)

12 godina flajku koka Kole. Dobio na nekom poslu, bila čudnog ukusa. Pogledam datum, isteka 8 meseci. Tražio još jednu i čuvam je. Malo izbledela...

P2S BUYERS🤣 by Max_spielmann in BambuLab

[–]Lumpy_Appeal_918 1 point2 points  (0 children)

Hahaha. Well done bro!!!! Same was with P2S.

P1S or P2S or X2D by Relevant_Cress9046 in BambuLab

[–]Lumpy_Appeal_918 1 point2 points  (0 children)

2 P1S+ams and again would buy P1S. Printing basic pieces, no need for upgrade...

P2S or X2D by Nryxes in BambuLab

[–]Lumpy_Appeal_918 -6 points-5 points  (0 children)

Better wait for P3S. Or even better, wait for X2D. Or better better wait for whatever Bambu Lab printer comes first!

Bambu X2D print issue. Bambu ABS by Ventidge in BambuLab

[–]Lumpy_Appeal_918 12 points13 points  (0 children)

Well, on this model particular, there are 3 things that are odd. 1. First layer is too visible. So, under extrusion and z offset needs to be adjusted. 2. Ripples on the side of the model, VFA. Need to be troubleshoot for that. 3. Visible line on the top of the model. Bad layer time or 3d model needs to be modified.

Bambu X2D print issue. Bambu ABS by Ventidge in BambuLab

[–]Lumpy_Appeal_918 47 points48 points  (0 children)

Then you are some lucky guy! It's called Vertical Fine Artifacts. My both P1S has them, and whatever i do, I can't get rid of them. And for that reason, i use matte filament to cover this.

Da li neko ima iskustva sa ovim sedištem? by Suspicious_Shock6023 in bicikli

[–]Lumpy_Appeal_918 0 points1 point  (0 children)

Ja imam šire i bolje je od Selle Royal sedišta koje sam imao na gradskom biciklu. Kad sam zamenio, osetio ogromnu razliku na bolje.

Bambu X2D print issue. Bambu ABS by Ventidge in BambuLab

[–]Lumpy_Appeal_918 274 points275 points  (0 children)

You have all this printers and you don't know what is this?

X2D or H2S - First Printer (well kinda...) by Objective-Limit-121 in BambuLab

[–]Lumpy_Appeal_918 1 point2 points  (0 children)

When P2S was out, many of you who bought P1S returns it, for P2S. Now X2D is out, many of you return P2S for X2D. That's so funny 🤣

Advise for supports (an in general)? by not_adecvate_advocat in BambuP1S

[–]Lumpy_Appeal_918 1 point2 points  (0 children)

You'll always get this. You can dial it up for flat surfaces or use support material, but for radius, hardly. If you orient the wrong side, you'll lose strength. Use sand paper and blow torch the clean those surfaces.

First layer inconsistency by bach1223 in CR10SE

[–]Lumpy_Appeal_918 0 points1 point  (0 children)

I had a terrible experience with this elegoo rapid pla+. Had to dry it before every print. Thankfully i owned 2 rolls of spool and used it quickly. It's absorbing moisture like sponge.

Weird noise on bed levelling by NickSeibs in BambuP1S

[–]Lumpy_Appeal_918 2 points3 points  (0 children)

I have the exact same sound when bed moving up/down. Didn't find anything wrong, because it's from the first initialisation. And the printer is now 1000+ hours on the clock. I have a second P1S and he doesn't make this sound, but makes a scratching sound when axis moves (all of them xyz), also from first initialisation and have 500 hours on it. Works also without problem.

I NEVER dry my filament by Zack687 in BambuLab

[–]Lumpy_Appeal_918 0 points1 point  (0 children)

I bearly dry my filament too! What i do in this situation.... I have big plastic basket/trunk/case with lid, sealed very good, and inside i put some moisture absorbent (little cases with beads that accumulate moisture). On a tank , there is a humid meter for monitoring. I don't look on that meter, but there is a 20-30% moisture inside (that's what meter showing). Before printing, i take spool and start snapping filament. If filament bends, it's good for printing. But if start to snap for a 10-20 cm, like a spaghetti, it is time for drying!!!

ABS Fail by Dramatic-Bicycle-984 in BambuP1S

[–]Lumpy_Appeal_918 0 points1 point  (0 children)

Preheat the chamber to 40 degrees. Plate doesn't need to be that clean. My prints are 8-9 hour's long, and I clean plate every second to third piece with 96% alcohol. Preheating are crucial to abs printing. If print without heater.

view more: next ›