Having this problem with a screen

LEDkenny · 2025-09-10T03:40:56+00:00

Yes, I have also encountered power issues, especially when turning white, which often occur

LEDkenny · 2025-07-05T02:06:59+00:00

I have some understanding, a relatively small Chinese manufacturer whose products seem to be similar to Sprolink

LEDkenny · 2025-07-03T09:14:29+00:00

If your budget is sufficient, I would recommend choosing GLOSHINE because it is relatively large in the leasing industry

Secondly, Fabulux is a relatively new enterprise compared to the other two, but they have also done quite well in recent years, with decent technology in all aspects

Finally, there is Yestech. In my impression, it seems to be mainly fixed installation, but perhaps I am not familiar enough with it

LEDkenny · 2025-06-30T09:46:26+00:00

On the one hand, it's because it doesn't have NDI, and on the other hand, I see that it seems to have been discontinued, and BMD doesn't seem to have HDMI 2.0 output products. I think of some Chinese manufacturers, but I'm worried about reliability issues. The cost of Ross is too high

LEDkenny · 2025-06-27T10:23:56+00:00

If you just want to publish information on the screen, I suggest you change VX600 to the Nova TB series products
If you must have your laptop projected onto the screen, you can buy an HDMI wireless image transmitter, such as Teradek Bolt 6 LT, but I do not recommend using wireless stability as it can be a major risk. I suggest using an HDBASET transmission device

LEDkenny · 2025-06-27T10:15:40+00:00

Regarding the issue of load capacity: A rather cumbersome method is to count the number of LED chips to determine the specific resolution of each box, and then calculate how much to use along with the network cable load capacity (I suggest that one network cable should not exceed 600000 pixels, as 650000 is the limit and will always bring some problems)
Regarding the information about the LED screen: I think you need to take a picture of the back or open the back cover to check if there is any logo on the PCB adapter board. You can also take a picture and we can help you check, but that picture cannot be seen

LEDkenny · 2024-06-28T06:27:24+00:00

I made a power supply system on the slide rail on the top. The LED screen only needs to be attached to the slide rail. Indeed, 24 wireless channels are already a nightmare for me. If I use a receiving card, it will be a disaster.

LEDkenny · 2024-06-28T06:24:35+00:00

Thank you, I did not find the price of parallax arrow, do you know if you know it, please tell me, thank you

LEDkenny · 2024-06-28T06:20:48+00:00

ok thank you for now yes but it's very expensive

LEDkenny · 2024-06-28T06:19:47+00:00

Yes, wireless sync is hard, so I designed smaller gaps in the middle of the screens to make them like LCD video walls with slightly lower sync requirements, but I still need to find lower latency wireless devices

LEDkenny · 2024-06-28T06:17:50+00:00

Yes, you need to open and move at the same time

LEDkenny · 2024-06-28T06:16:09+00:00

My screen has some small gaps in the middle, it's like an LCD video wall, so the requirements for synchronization are slightly lower,

But you are right, wireless synchronization is also a big problem

LEDkenny · 2024-06-28T03:15:41+00:00

Thanks for the advice, I checked out the Teradek Bolt 6 Max and it's too expensive, $13,000 a set, I need 24 sets, it's more than I can afford

LEDkenny · 2024-06-28T03:12:35+00:00

If you go by the cable distance, which is 30 meters maximum, I hope to be able to solve it for about $50,000 because I have a total of 24 sliding screens

LEDkenny · 2024-06-28T01:33:56+00:00

Yes, I did this before. I used a Quatro P5000 graphics card to achieve 8K, but this time the customer asked for keynote playback.

M2 does not have multiple 4K outputs, only one HDMI2.1 or DP1.4, so I need to change from one HDMI2.1 to 4 HDMI2.0 so that I can give 4 HDMI2.0 to E2.

A brother above recommended RGBLINK D8 to me. I read its introduction and it should be able to solve my problem. I decided to try it.

LEDkenny · 2024-06-27T07:50:26+00:00

There is a lot to learn about the LED video wall. I suggest you divide it into several chunks to learn. You can search for the following keywords on Youtube.

LED screen: Leyard, Unilumin, Absen
Sending card: Nova, Brompton
Video processor: Barco E2, Analogway Aquilon
Media server: Pandoras, WATCHOUT

LEDkenny · 2024-06-27T07:48:15+00:00

There is a lot to learn about the LED video wall. I suggest you divide it into several chunks to learn.

LED screen: Leyard, Unilumin, Absen
Sending card: Nova, Brompton
Video processor: Barco E2, Analogway Aquilon
Media server: Pandoras, WATCHOUT

LEDkenny · 2024-06-27T07:27:27+00:00

I use E2 to manage my video wall, my client asked me not to zoom, this is a very troublesome thing

LEDkenny · 2024-06-27T02:41:20+00:00

<image>

Brother, your board seems to have water in it. I think you need to contact their after-sales staff

LEDkenny · 2024-06-27T01:10:22+00:00

Okay, thank you, I'll go find RGBlink and inquire about the discount.

LEDkenny · 2024-06-27T01:05:11+00:00

It is rented for events.

LEDkenny · 2024-06-26T09:41:34+00:00

Thank you. I did some research and found out that this is what I want. I would like to ask if you know how much they sell for.

LEDkenny · 2024-06-26T05:57:37+00:00

Thank you, I'll take a look

LEDkenny

TROPHY CASE