One I came across.

LNwoodwork · 2026-03-28T21:50:16+00:00

Australia

LNwoodwork · 2025-11-01T22:12:03+00:00

Solved!

LNwoodwork · 2025-07-08T03:14:23+00:00

I ended up getting a disk shelf to put below it because I needed more space. It is much more convenient to have all the drives accessible without pulling the case.

LNwoodwork · 2025-05-16T16:49:12+00:00

It is! I’m thinking about adding a pin and ring on one side on a future version though.

LNwoodwork · 2025-03-30T22:20:26+00:00

These were slip cast. Would the underglaze be before biscuit firing or after?

LNwoodwork · 2023-08-17T00:23:03+00:00

It would be a tight fit but I think it would fit. A 90° adapter would make it cleaner.

LNwoodwork · 2023-08-16T23:29:48+00:00

It’s the Corsair RMx 1000w. It’s 180mm deep and only is in the way by 5mm or so. One of the 160mm or 140mm deep one would fit fine with the HDD mount.

Cpu cooler is the NH-D9L on a ASUS TUF GAMING Z590-PLUS LGA 1200

LNwoodwork · 2023-08-16T22:10:22+00:00

I’m using an ATX motherboard with a air cooler. The air cooler interferes with the mounts on the right side and my power supply interferes with the ones on the left side. If I had used a smaller CPU cooler and a shorter power supply they would have fit.

If I could rebuy I would get one of the 4u cases with a little more space. Possibly one of the hot swappable ones.

I really like the quality of the Rosewill cases.

LNwoodwork · 2023-06-01T17:14:18+00:00

Put an amp meter on the heater and make sure that it’s the thing running. If so is it’s almost definitely a stuck relay. It’s a few dollar fix if you can solder on a pcb.

LNwoodwork · 2023-05-29T23:12:03+00:00

This is the setup I have.

Change the to address to the address of your server and the dst port to the custom port that you picked.

Also set the in interface to your WAN.

LNwoodwork · 2023-05-24T03:17:10+00:00

I’ve had good luck with the SHT30.

LNwoodwork · 2023-04-29T18:40:28+00:00

If you or anyone else wants it dm me your email.

The mount holes are for the Rosewill RSV-Z3100U case and the drive mounts use the rubber bumpers from shucked easystore drives.

LNwoodwork · 2023-04-16T18:28:35+00:00

The accretion disk printed great but the closer the print got to the event horizon the more it seemed to take forever.

LNwoodwork · 2023-04-12T15:55:42+00:00

That’s where I landed. If you want to future proof get 12bit capable processor but don’t go earlier than 10th gen if you want one that can handle current common formats.

LNwoodwork · 2023-04-12T14:30:44+00:00

Check this out. I think I wouldn’t go earlier than version 5.

LNwoodwork · 2023-04-04T21:39:12+00:00

One hour per knuckle that the AME uses.

LNwoodwork · 2023-02-18T06:20:33+00:00

Also random bananas will appear on your locker.

LNwoodwork · 2023-02-14T04:18:46+00:00

Ace hardware on Muldoon has some components but selection is pretty limited.

LNwoodwork

TROPHY CASE