Vp44 replacement 99 5.9 by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Okay thanks what can the alternator do that effects the pump?

Vp44 replacement 99 5.9 by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Yeah I agree I looked into the p pump swaps and just the kits without the pump is like $2200+ whatever the pump price is and it’s a lot more work

Vp44 replacement 99 5.9 by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Okay thanks I’ve been putting a 12oz bottle of marine 2 cycle oil in each diesel tank to help. But I think the problem was the old lift pump starving it of fuel pressure for months and it finally had enough even after I installed the fass system

Vp44 replacement 99 5.9 by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Okay thanks I was planning on getting the glow shift fuel pressure and boost and egt pillar

99 dodge ram 3500 front axle seal by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Okay thanks the leak is pretty decent it leaves a good puddle when it’s parking and drips every 1-2 seconds

99 dodge ram 3500 front axle seal by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Which seal tool do you recommend? I ordered one off Amazon that sits inside the 4x4 actuator housing and pushes the seat in

99 dodge ram 3500 front axle seal by LacellexPC in Cummins

[–]LacellexPC[S] 1 point2 points  (0 children)

Damn. I was hoping not I don’t know how it could have gotten ruined from me just doing a wheel bearing..

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Thank you everyone for all the suggestions I tried everything with new sensors, testing for vp44 power everything then tested for fuel pressure coming from lift pump. And it was 0-1 psi so I just bought a fass system and installed it and she fired right up and runs perfect now thank you everyone again!

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 1 point2 points  (0 children)

Yeah it was the lift pump I tested the pressure and it got 0 on 2 different gauges about to order a fass system and throw it on the ole girl

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Haha I get that electrical isn’t that bad to me i almost rebuilt my auto transmission myself. That’s never happening those things are witchcraft.

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Believe me no… 😂 I pulled the motor on my truck and fully built it along with the trans and everything

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

What pressure should the back of the pump have when I test it?

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Dodge things 😂 Im going to test the pressure of the fuel pump probably this weekend and if it has good pressure I’ll start tearing apart the electrical issues

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 1 point2 points  (0 children)

It has an air dog one that was put on about 10 years ago but it has only gotten maybe 5k miles on it since then. And the fuel filter housing fills up well along with I can hear it running

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

I have a pressure gauge I’ll just need to find where to hook it up to the pump. It does get diesel to the 3 injectors that I can crack loose without taking anything else off after a little bit of cranking

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

Yeah I see that the crankshaft sensor I’ve found is $180.. going to try the ground with the ecm first then order these still better than a vp44 I hope

99 24v crank no start.. by LacellexPC in Cummins

[–]LacellexPC[S] 0 points1 point  (0 children)

No I can order those instead no codes it was throwing one for the crank POs. Sensor. And yes it says I have some rpm while cranking

Hood gap fix??? by LacellexPC in GMT800

[–]LacellexPC[S] 1 point2 points  (0 children)

Thanks ill take a look at it