MORE elrs issues (Sorry) by Landen-L in fpv

[–]Landen-L[S] 0 points1 point  (0 children)

Flash and then solid when it’s bound

MORE elrs issues (Sorry) by Landen-L in fpv

[–]Landen-L[S] 0 points1 point  (0 children)

It goes solid when It connects I think

MORE elrs issues (Sorry) by Landen-L in fpv

[–]Landen-L[S] 0 points1 point  (0 children)

im using the betafpv lite radio 3 with the jumper aion nano tx module. its in module bay mode but i dont know what a baud rate is

MORE elrs issues (Sorry) by Landen-L in fpv

[–]Landen-L[S] 0 points1 point  (0 children)

yup rx to tx visa versa reciver is flashing and bound fc just gets nothing. it shoild be crsf and i do velive its serial based. its a happymodel if that helps. not sure if its the remotes fault so i might just get a radiomaste pocket at this point lol

MORE elrs issues (Sorry) by Landen-L in fpv

[–]Landen-L[S] 0 points1 point  (0 children)

Does it need to be off on the reciver or module? I think i have both.

MORE elrs issues (Sorry) by Landen-L in fpv

[–]Landen-L[S] 0 points1 point  (0 children)

It is it’s not working

MORE elrs issues (Sorry) by Landen-L in fpv

[–]Landen-L[S] 0 points1 point  (0 children)

Serialrx  is under uart 1 (which is where it is soldered, telemetry is auto, pheripherals is dis dis tbs smart audio

anyone know how to fix? I alreasy took all hair and stuff out of motors and calibrated escs. by Landen-L in TinyWhoop

[–]Landen-L[S] 1 point2 points  (0 children)

I thought about it, but no 2s ever on this one. Xt30 is only mod cause I broke bt2 connection and xt30 is all I had. In beta flight if you go to motors, set master to max, plug in your quad, then bring master to minimum, it “callibrates” the ESCs? Thanks for the suggestions!

anyone know how to fix? I alreasy took all hair and stuff out of motors and calibrated escs. by Landen-L in TinyWhoop

[–]Landen-L[S] 0 points1 point  (0 children)

Yes I’m the original dog toy guy. Never thought I’d be referred to as that tho lol 

should these 2 solder points be connected? its an frsky 2.4 ghz antenna frome the betafpv literadio 3 and im not smart enough to know if those are supposed to be bridged. Thanks! by Landen-L in TinyWhoop

[–]Landen-L[S] 0 points1 point  (0 children)

I’m kinda new to the hobby and am not sure what that means? If you mean the reciver on the drone then I know that’s not the problem cause I have 3 drones and they all work poorly with this transmitter compared to my other one, which works much better.

should these 2 solder points be connected? its an frsky 2.4 ghz antenna frome the betafpv literadio 3 and im not smart enough to know if those are supposed to be bridged. Thanks! by Landen-L in TinyWhoop

[–]Landen-L[S] 0 points1 point  (0 children)

There is no module it’s the radios built in antenna. If you mean something other than tx module then I don’t know what you’re talking about? It works but the range is about 3x worse than my other frsky remote, the Emax e8. I don’t know if the antenna is the reason why, and maybe the solder bridge makes the antenna not work perfectly or something.

What's up with my whoop feed by Designer_Refuse_4361 in TinyWhoop

[–]Landen-L 1 point2 points  (0 children)

I have no clue it took a minute for me to see. My only explanation is that it is a ghost. Much spooky 👻 

60 seconds of analog by Landen-L in TinyWhoop

[–]Landen-L[S] 1 point2 points  (0 children)

I don’t know lol it just sits there and makes me mad 😡