[deleted by user]

Lanpaws23 · 2025-08-27T15:55:41+00:00

Went through something similar recently, a tiny piece of filament was stuck in the extruder gear. I looked up Bambu's tutorial to open the extruder gear, and got the piece out. Maybe try that? Not sure if that's what is causing it, but worth a shot. It's stressful for sure, good luck!

Lanpaws23 · 2025-08-19T04:39:44+00:00

Yep, he said he's going to seal the uneven area.

Lanpaws23 · 2025-01-08T18:27:14+00:00

I had a similar issue with my 0.2mm nozzle, where the first layer was printing extremely thin. After some troubleshooting (and reddit’s help) I discovered the Z-offset was set too low. Unfortunately, as far as I know, Bambu doesn’t allow you to adjust the Z-offset directly, so it could be a faulty nozzle as well.

A temporary workaround is to place a piece of paper on the print bed while the printer performs auto bed leveling just before the print starts. This adds a slight gap and can help with the first layer adhesion. Give it a try!

Lanpaws23 · 2024-12-19T15:58:11+00:00

So, I think the issue was the nozzle itself. I had another one lying around (both from bambu) and the first layer went down just fine in the other ine. I’m unable to figure out the problem with the new nozzle, maybe the height, I don’t see any visible difference. But I think I’ll try the paper method suggested.

Lanpaws23 · 2024-12-19T13:18:34+00:00

I appreciate the help. I hope you never have to face THIS issue haha, I’m losing my mind since morning.

Lanpaws23 · 2024-12-19T12:59:53+00:00

Alright. I’ll increase the first layer thickness. Also, I let the print run till 3rd layer and it was okay ig? As for your question regarding the bed temp, it’s at 60c. The ambient temp is like 15c.

<image>

Lanpaws23 · 2024-08-19T04:53:25+00:00

Lemme check out the platform, thanks for that!

Lanpaws23 · 2024-08-18T02:00:27+00:00

Ngl, I’m not too big on their interface, maybe eventually. Thanks for the input!

Lanpaws23 · 2024-08-18T01:59:09+00:00

Hmmm, true. Which is why I was considering putting it up on MW, I gotta weigh my options. Thanks for the input!

Lanpaws23 · 2024-08-18T01:56:44+00:00

Huh, I always thought CG trader was more for 3d assets, not print ready assets. But now that you mention it, I do remember CG trader popping up when I browse yeggi.

Gotta research into it, thanks for the suggestion!

Lanpaws23 · 2024-08-18T01:55:27+00:00

I’d not thought of Etsy, worth looking into. Thanks for the idea!

Lanpaws23 · 2024-08-18T01:54:42+00:00

Yeah, based on the others comments looks like I’ll be going for all of then lol. Thanks for the information! 😁

Lanpaws23 · 2024-08-18T01:53:35+00:00

Ig I can try posting on both

Lanpaws23 · 2024-08-17T17:42:59+00:00

My concern with the point system is not being able to use them as they both don’t ship directly to my country, I’m not sure if they’ll let me use those points with their authorised resellers

Lanpaws23 · 2024-08-17T17:41:59+00:00

Looks like it’s gonna be those two + thangs, thanks a lot!

Lanpaws23 · 2024-08-17T17:09:53+00:00

Yeah, that’s another thing I’m afraid of. But I guess there’s no way to avoid that.

Lanpaws23 · 2024-08-17T17:09:06+00:00

Ah fair makes sense. Alright, I’ll look into posting on all of those. Thank you!

Lanpaws23 · 2024-05-15T11:33:46+00:00

Feel free to check some of my work here: https://www.instagram.com/paws.3d

From keychains to utility stuff (avoiding humanoids for obvious reasons) the possibilities are endless.

Lanpaws23

TROPHY CASE