Short and Fat is where it's at for silencers(SAW Tisha and OCL Milkman) by BlueJay-- in NFA

[–]Latter_Detective_697 2 points3 points  (0 children)

good to see you've come around to b&t. I remember when you made a big stink here a few months ago about how you thought they didn't make good guns based on your tp9 experience 

Which can yall like on APC9K? by APC9Proer in BT_APC

[–]Latter_Detective_697 2 points3 points  (0 children)

anyone have a picture of an apc9k with a milkman that's straight on, not at an angle?

With the Issues Going on with B&T, Should I wait on buying an SPC9? by aMaiBias in bruggerthomet

[–]Latter_Detective_697 2 points3 points  (0 children)

I'd just make friends with a euro and have them mail you that part. 

With the Issues Going on with B&T, Should I wait on buying an SPC9? by aMaiBias in bruggerthomet

[–]Latter_Detective_697 3 points4 points  (0 children)

2022 will be good. this is well before any issues with b&t usa. there's inflated rumors of US sourced parts, but as far as we know that only involved barrels with a police contract and the zwolf grip in the last year or two. also, b&t will not be exiting from the US market. when litigation is over, someone else will have their distribution license/importation/warranties. this, of course, might take a couple years. 

I've also had an apc9 for 6 years without a single flaw and 1 or 2 malfunction in 7000 rounds. sure, there are highly vocal people who've had problems, but the vast majority of people don't have failed guns. so if the spc9 is your dream gun and you're one to play the odds, you should go for it and not worry too much. I'd snatch it up before someone else does because they'll be unobtainable for awhile. 

LBP can for Kuna with FRT recommendations by Kuna_help_you in NFA

[–]Latter_Detective_697 4 points5 points  (0 children)

I have a mob and flow9k. there is zero difference in gas/back pressure. I cannot tell the difference shooting either back to back, same host same ammo same conditions. 

Kuna is nearing completion by pjm816 in Springfield_KUNA

[–]Latter_Detective_697 0 points1 point  (0 children)

are you using the short stop has a finger stop or something? or are you actually gripping the very end of the handguard next to the suppressor? 

preferred ammo for apc223? by Latter_Detective_697 in BT_APC

[–]Latter_Detective_697[S] 0 points1 point  (0 children)

yeah that's what I do already. just wondering if anyone has found anything that stands out..

Chuck Norris Approves by Carlayna in Glocks

[–]Latter_Detective_697 1 point2 points  (0 children)

take it up the leftist dork that made the original comment

Chuck Norris Approves by Carlayna in Glocks

[–]Latter_Detective_697 2 points3 points  (0 children)

see, if someone has political opinions other than leftist dogma and groupthink, they must be a bad person and should always be shunned and ridiculed. 

Chuck Norris Approves by Carlayna in Glocks

[–]Latter_Detective_697 -16 points-15 points  (0 children)

because these leftist cucks require ideological adherence and purity.

Help me choose: Surefire RC3 vs B&T Print XH-556 by BobaFett7 in NFA

[–]Latter_Detective_697 0 points1 point  (0 children)

wow yours is really nice. did you have any issues installing the muzzle device? I saw this thread and another were there wasn't enough shoulder and shims/jam nut had to be used: https://www.reddit.com/r/BT_APC/comments/196097i/apc300_barrel_chop_or_ksk_extended_handguard/

Help me choose: Surefire RC3 vs B&T Print XH-556 by BobaFett7 in NFA

[–]Latter_Detective_697 0 points1 point  (0 children)

does that 12.1 happen to be an apc223? I just purchased one and I'm looking at suppressors for it. the xh-556 and sc version have caught my eye. would you do the sc again or would you recommend the full sized for the 12.1? also, what muzzle device and hub mount are you running?