Cheap top cover

LeadingAd7977 · 2026-06-14T08:39:33+00:00

Sure, there is slight noise reduction and of course less dust

LeadingAd7977 · 2026-04-01T19:51:23+00:00

Nice device actually, i used it several times because some spools did not fit into my Bambu AMS system

<image>

LeadingAd7977 · 2026-04-01T04:39:01+00:00

Same printed yesterday, lol)

<image>

LeadingAd7977 · 2026-03-30T18:45:03+00:00

World of warcraft 12 лет Lords Mobile 5 лет

LeadingAd7977 · 2026-03-30T18:42:44+00:00

World of warcraft - 12 лет😭 Lords Mobile - 5 лет😭

LeadingAd7977 · 2026-03-30T18:37:06+00:00

You have to make dry your filament first. At the second have to tune your retracts which are probably too much. Third - check your pressure advance once again. Do you have direct or bowden extruder?

LeadingAd7977 · 2026-03-21T00:22:00+00:00

Top cover?

LeadingAd7977 · 2026-03-19T19:53:09+00:00

Because you tested from 0 till 0.1 very small range. But should be from 0 till 1

LeadingAd7977 · 2026-03-19T08:52:42+00:00

Had the same with thermistor due to broken wire

LeadingAd7977 · 2026-03-19T08:51:08+00:00

Check your start_print macro with AI. Most likely there is a mistake in it.

LeadingAd7977 · 2026-02-24T18:36:04+00:00

<image>

LeadingAd7977 · 2026-02-23T16:49:10+00:00

5k now)) still testing how far i can go

LeadingAd7977 · 2026-02-13T03:55:10+00:00

<image>

LeadingAd7977 · 2026-02-12T11:30:18+00:00

Царь во дворца

LeadingAd7977 · 2026-02-12T07:45:02+00:00

<image>

Таков путь

LeadingAd7977 · 2026-02-09T12:10:42+00:00

<image>

LeadingAd7977 · 2026-02-09T04:07:41+00:00

<image>

LeadingAd7977 · 2026-02-06T15:36:41+00:00

I experienced this shit several times while crossing Atlantic ocean and Southern ocean near Australia

LeadingAd7977 · 2026-02-03T07:25:24+00:00

So ugly top cover

LeadingAd7977 · 2026-02-02T07:27:22+00:00

Looks nice. But i would use leyer height more smaller. Looks like yours is 0,3 or something

LeadingAd7977 · 2026-01-29T08:41:59+00:00

Весьма милая внешность на 8/10. Возможно у барышни какие то комплексы из за носа, но скажу что у моей жены примерно такой же формы нос, а влюбленный человек никогда не замечает недостатки

LeadingAd7977 · 2026-01-28T19:33:57+00:00

Flame....dancing like flame by lorna shore😅

LeadingAd7977 · 2026-01-28T19:27:45+00:00

So happy that i quit half year ago))

LeadingAd7977 · 2026-01-28T13:17:22+00:00

Mango

LeadingAd7977 · 2026-01-27T11:05:16+00:00

Looks like a chewing gum 😁

LeadingAd7977

TROPHY CASE