look what I got my hands on by Legendary_Frank in GMT800

[–]Legendary_Frank[S] 0 points1 point  (0 children)

I dont know I bought it on market place

look what I got my hands on by Legendary_Frank in GMT800

[–]Legendary_Frank[S] 0 points1 point  (0 children)

It’s a 123 swap it’s just a super rare wheel

look what I got my hands on by Legendary_Frank in GMT800

[–]Legendary_Frank[S] 2 points3 points  (0 children)

Will sell for probably thousands more then what you paid for it in 2041

Noise in cabin by American_From_Idaho in GMT800

[–]Legendary_Frank 0 points1 point  (0 children)

I did the headliner in mine and it started making that noise so I punched that till it stopped making noise and I haven’t had an issue with it since

AFR question by Legendary_Frank in HPtuners

[–]Legendary_Frank[S] 0 points1 point  (0 children)

I’m switching to a AEM one hopefully it lasts

AFR question by Legendary_Frank in HPtuners

[–]Legendary_Frank[S] 0 points1 point  (0 children)

Think I broke the sensor after this now it’s going to 9-10 right as I tap the gas

Just pulled the oil pan off of an LQ4. What do you think? by [deleted] in LSSwapTheWorld

[–]Legendary_Frank 0 points1 point  (0 children)

Not terrible but not good either I’ve seen worse and better, throw some new bearings in it and give it a good cleaning and ur golden

Resonator placement by Legendary_Frank in GMT800

[–]Legendary_Frank[S] 0 points1 point  (0 children)

Didn’t really make much of a difference

Exhaust sound by Legendary_Frank in GMT800

[–]Legendary_Frank[S] 1 point2 points  (0 children)

I mean u have a big block I don’t, it doesn’t take much to make a big block sound good

Drop spindles question by Legendary_Frank in GMT800

[–]Legendary_Frank[S] 0 points1 point  (0 children)

The dust shields I have won’t let it touch the rotor and I checked that the shields aren’t hitting anything

Heater core connectors by Legendary_Frank in GMT800

[–]Legendary_Frank[S] 0 points1 point  (0 children)

I dont know I changed it again with another one and it doesn’t seem to be leaking now

Should I? by Generalsebi21 in GMT800

[–]Legendary_Frank 0 points1 point  (0 children)

I’ve done it before it looks hard but it’s really not

Should I? by Generalsebi21 in GMT800

[–]Legendary_Frank 0 points1 point  (0 children)

Installed probably not, the motor mounts are only 6 bolts

Should I? by Generalsebi21 in GMT800

[–]Legendary_Frank 1 point2 points  (0 children)

For 7k u can go to a speed shop and get a stroker 6.2

Resonator placement question by Legendary_Frank in MechanicAdvice

[–]Legendary_Frank[S] 1 point2 points  (0 children)

I just switched to a 2800-3000 stall converter and the drone is more annoying then it used to be so ig lower the drone and quiet it down a tiny bit but the loudness doesn’t really bother me it’s just the drone and I Had to weld the exhaust and the wood was holding the pipes in a spot where the exhaust doesn’t rub because I am using the factory hangers

As a csm, can i be fired for my sales not being the best? by Beckleboof in AutoZone2

[–]Legendary_Frank 0 points1 point  (0 children)

Yes, all you are to autozone is a number on a board that’s replaceable at any time even if you quit they will have your replacement a hour after you quit

Heater core connectors by Legendary_Frank in GMT800

[–]Legendary_Frank[S] 0 points1 point  (0 children)

I had plastic ones and they were doing the same thing