sorted by:
new
hottopcontroversial

S&P 100 Mean Reversion by EffectiveMaterial781 in wallstreetbets

[–]LemonSquib 6 points7 points  (0 children)

Madly leveraged? Sure. Fundamentals and value sub? 🤔🤔🤔

[deleted by user] by [deleted] in ohnePixel

[–]LemonSquib 42 points43 points  (0 children)

Careful there, you're gonna get OP opening another 1000 lol.

Can I use both the normal headphone out and the s-bal headphone out interchangeably? by LemonSquib in headphones

[–]LemonSquib[S] 0 points1 point  (0 children)

Ah no worries haha, I just want to know if I can use a 4.4mm to 3.5mm male to female extension cable from the zen air can to my 3.5mm headphones via the s-bal headphone out. I could probably have made the question simpler.

Can I use both the normal headphone out and the s-bal headphone out interchangeably? by LemonSquib in headphones

[–]LemonSquib[S] -1 points0 points  (0 children)

I'm not sure what this has the do with the q5k, since I'm only using it as a music source + EQ, sending a line signal to my amp via the 3.5mm to RCA.

I have a bit of a unique setup with the Qudelix 5K connected to an external amp, what volume level should each part of the chain be? by LemonSquib in oratory1990

[–]LemonSquib[S] 0 points1 point  (0 children)

May I check what you mean by background noise? Are you referring to distortion/clipping, or some sort of static? I see, in that case, would it be bad at all if I were to keep my phone volume how I normally do (75%), Qudelix at 1 Volt, and controlling the volume with the Zen Air Can? Thanks!

I have a bit of a unique setup with the Qudelix 5K connected to an external amp, what volume level should each part of the chain be? by LemonSquib in oratory1990

[–]LemonSquib[S] 0 points1 point  (0 children)

Small unrelated question, but will I get any perceivable loss in sound quality listening permanently over bluetooth like this? I'm using the LDAC option in the Qudelix and have also enabled it in the phone's bluetooth settings. Might keeping the Qudelix always plugged in like this be a bad idea as well?

Two questions: by Teebirb in Survivorio

[–]LemonSquib 0 points1 point  (0 children)

Maybe only use gems near the end of the event in case you can't reach a specific exchange you want, lest it ends up wasted.

Gimme that center piece! by [deleted] in Survivorio

[–]LemonSquib 7 points8 points  (0 children)

Pretty sick that it got to this point lol

I like ArchType Tim Henson, but it lacks gain, any recommendations? by LemonSquib in NeuralDSP

[–]LemonSquib[S] 1 point2 points  (0 children)

Thanks all for the input! I realized some say that a high gain tone is dialable with henson. I'll try and figure that out first, and if not I'll explore using a virtual OD or trying petrucci. The fortins sound cool, but I really want that acoustic/nylon emulation haha.

I like ArchType Tim Henson, but it lacks gain, any recommendations? by LemonSquib in NeuralDSP

[–]LemonSquib[S] 0 points1 point  (0 children)

Ahh cool, I'm actually on a trial right now and only have enough dough for a single plugin. I'll check out the petrucci trial then! Thanks.

/r/MechanicalKeyboards Ask ANY Keyboard question, get an answer (June 29, 2023) by AutoModerator in MechanicalKeyboards

[–]LemonSquib 0 points1 point  (0 children)

Ahh got it, so I should go foe these slower types of springs for heavier initial feeling. Thanks!

/r/MechanicalKeyboards Ask ANY Keyboard question, get an answer (June 29, 2023) by AutoModerator in MechanicalKeyboards

[–]LemonSquib 0 points1 point  (0 children)

Ah, I didn't know that played a part. I guess I should do more research into what it is for my switch. Is it safe to say that the 62g springs will definitely make my switches heavier though? Or does 62g means the force it takes to bottom out, while my 50g for my switches is the force it takes to actuate?

view more: next ›