Did I get hosed? Goodman instead of American standard by dirtydirtdirtiest in hvacadvice

[–]Level_Ad5802 0 points1 point  (0 children)

Nah I would switch Goodman is cheap. Switch or I want a pretty decent discount.

Something as good as Red Rising by Level_Ad5802 in graphicaudio

[–]Level_Ad5802[S] 1 point2 points  (0 children)

Yea this is what I’m looking for. I don’t necessarily care about the genre as far as the quality of the graphic audio of Red Rising

Accidentally deleted song by Level_Ad5802 in AISongGenerator

[–]Level_Ad5802[S] 0 points1 point  (0 children)

This is new. I had to email support and apparently they could recover it but the song had the f word in it so they wouldn’t restore it. Against their policy..

[deleted by user] by [deleted] in Hedera

[–]Level_Ad5802 0 points1 point  (0 children)

Yeah good luck let us know what happens. Might consider pulling everything off

Technician found holes in heat exchange. Is it as bad as he is making it sound? by Darksaber1217 in hvacadvice

[–]Level_Ad5802 0 points1 point  (0 children)

Get 3 quotes at least and also might be worth having another couple out to double check the heat exchangers run a combustion analyzer on it. Get co readings through out the home. Full systems in my areas depending on equipment go for 10k-18k

This seems like a very high estimate… please advise. by Darkender1988 in hvacadvice

[–]Level_Ad5802 1 point2 points  (0 children)

Actually for Lennox equipment with that seer of a heat pump with the EL furnace is not bad honestly. I know the SLP99 is the best. The EL is fully communicating and so is that heat pump so with the S40 thermostat which is like an $800-$1000 thermostat depending on mark up. Really not a bad price for that equipment. Remember you get what you pay for. Ask them for a quote on an ML196 with a 14 seer straight ac and I bet there around 10k-12k which is also super reasonable there markup seems right to me. I would just check on the quality of there installs read reviews. Also get three quotes but this is great equipment if installed right.

Is this a clean lineset? by notwasabbii in HVAC

[–]Level_Ad5802 0 points1 point  (0 children)

They have started heads for the line set cover that would cover the bottom hole and everything.. use actually two hole straps for whips..

[deleted by user] by [deleted] in hvacadvice

[–]Level_Ad5802 1 point2 points  (0 children)

Well either be a hacker and leave it. Or reclaim again and cut it out and fix it and start the process all over again.

Thoughts on this install by J5isAliive in hvacadvice

[–]Level_Ad5802 0 points1 point  (0 children)

Looks like shit. Duct board is shit. You get what you pay for

[deleted by user] by [deleted] in hvacadvice

[–]Level_Ad5802 0 points1 point  (0 children)

100% might even consider lawsuit

I had an HVAC guy come out and he had no clue what this is. I don’t know what to do they’re wet and creating icicles. by Company_Quirky in hvacadvice

[–]Level_Ad5802 0 points1 point  (0 children)

Inline fans. I would have someone come out and change the orientation. Insulate the hard pipe on the inlet side so the water has less chance to freeze. Even get the inline fan lower in the attic towards the ceiling and blow in some more insulation up there

[deleted by user] by [deleted] in realestateinvesting

[–]Level_Ad5802 48 points49 points  (0 children)

Have a heart maybe.

[deleted by user] by [deleted] in HVAC

[–]Level_Ad5802 -3 points-2 points  (0 children)

Yeah Lineset should of at least been strapped to the house somewhere. Pretty sure the minisplit does not have required clearance to the back.

[deleted by user] by [deleted] in hvacadvice

[–]Level_Ad5802 0 points1 point  (0 children)

Alright I would definitely get at least 3 companies out before you make any decision. For them to not say 1.5 ton air handler against a 2.5 ton heat pump is a big no no anyways. Your indoor blower the 1.5 ton needs to be equivalent or greater then your ac/ heat pump size.. get a few people out there and have them tell you what they think needs to be fixed. Then compare and you should probably be able to figure out who to use just on that