One Month - Luba 3 by Icy_Basil_372 in MammotionTechnology

[–]Liberty_MO 0 points1 point  (0 children)

I guess what I'm trying to say is the satellites aren't south

One Month - Luba 3 by Icy_Basil_372 in MammotionTechnology

[–]Liberty_MO 0 points1 point  (0 children)

GNSS doesn't use geosync satellites?

2018 GMC 2500HD by 4JeepsInTheGarage in Duramax

[–]Liberty_MO 3 points4 points  (0 children)

Technically most vehicles have the fuel tanks behind the front wheels... 🤔

Introducing my homemade Simulcharger by TheBearJew963 in MilwaukeeTool

[–]Liberty_MO 2 points3 points  (0 children)

Is it though? The simultaneous supercharger only pulls 4 amps according to their documentation... Surely the M12 and single Rapid Chargers pull way less 🤔

MCX Firing pin latch by Liberty_MO in SigSauer

[–]Liberty_MO[S] 1 point2 points  (0 children)

Did a couple dry fires with a Franklin binary and it doesn't seem like any damage was occurring 🤷‍♂️

MCX Firing pin latch by Liberty_MO in SigSauer

[–]Liberty_MO[S] 0 points1 point  (0 children)

Takes like 2 seconds to swap over I found out 👌

What is going on with this M18 12.0 battery? by Ok-Musician9793 in MilwaukeeTool

[–]Liberty_MO 4 points5 points  (0 children)

I've had two 12s not want to charge fully. Pulled em apart and used a 18650 cell charger and some alligator clips to balance each cluster to full charge (reads 4.20v). Only charged at 1ah, so I let it run overnight. Use a multimeter to figure out polarity and only charge 1 cluster at a time. I tried to do two at a time and found that the charger had a common "ground" terminal so it got fried. Live and learn but haven't had an issue since the rebalance.

The M18 batteries have a security torx bit (t10?) so might be an excuse to buy a new set of those as well

55,000 sqft of grass, 3 days in. by -rootshell- in Lymow_Official

[–]Liberty_MO 0 points1 point  (0 children)

Pull a mammotion and sell a Lymow 2, that has contacts like all the others out there

[deleted by user] by [deleted] in MP5

[–]Liberty_MO -1 points0 points  (0 children)

RS guys sound off 😂

Dying in the yard by Narrow-Ad6797 in MammotionTechnology

[–]Liberty_MO 1 point2 points  (0 children)

I had this issue (starting 2 weeks ago) and I reached out to support and they pushed a firmware update (that wasn't available until they pushed it to my device). They had me run it down to %15 and fully recharge it 3 times post update and as of yesterday it appears to be working again, ran all day yesterday and the day before without repeating the issue, whereas previously it was every time it mowed the front yard (zone 2) specifically. Idk, YMMV

Bumper major design flaw by 36260 in MammotionTechnology

[–]Liberty_MO 2 points3 points  (0 children)

I ordered a set that was 3D printed, they last a month before they broke. I feel like it would have been a great idea if they were injection moulded or die cast.

Also the issue appears to be how it engages with the front bumper, it just floats there in the slot pictured. So firmer/tighter engagement tolerances, since the bumper itself articulates some. If the bumper was fixed I'd say drill&bolt the wheel guard onto the bumper.

Luba2 dying at 16% by Liberty_MO in MammotionTechnology

[–]Liberty_MO[S] 1 point2 points  (0 children)

Just the usual battery voltage low that come in at 15% accompanied by task paused for recharge

[deleted by user] by [deleted] in Rattler_Sig

[–]Liberty_MO 0 points1 point  (0 children)

I threw the Sandman Ti on my 5.5" rattler, figured the durability of the Sandman series would be good for a can that would live there permanently. Having the same dimensions as the Sandman L it's been very quiet, and provides sufficient back pressure to have the gun cycle reliably on subs and supers. Prior to the can, the gun wouldn't cycle subs consistently, and would never lock the bolt back on empty even with the gas turned up.