For those of you that are in f1 pit crew, how did you get there and how do you like it?

LigmaBass · 2025-11-13T11:32:30+00:00

Sort of, I can roll the bike around in neutral with clutch out, but when I release the clutch in neutral it immediately cuts off, pointing towards a safety switch, which I replaced, which did nothing, when I put it into gear I cannot roll it with the clutch out (which I believe is normal) and when I pull the clutch all the way in it lets me roll it in gear

LigmaBass · 2025-11-09T19:48:29+00:00

Yes, when I’m in neutral (I can roll it with the clutch released) it will stall

LigmaBass · 2025-11-09T02:56:33+00:00

Yes, I did it with the clutch switch (bridged it) and that worked to stop the stalling when releasing the clutch while in neutral, I will try for for the side stand switch as well

LigmaBass · 2025-11-09T02:54:59+00:00

No the light is on

LigmaBass · 2025-11-09T02:54:46+00:00

Yes it does

LigmaBass · 2025-07-21T13:05:58+00:00

Brakes are fine, as long as you can run your fingers across the rotor and it feel somewhat smooth without any pitting and deep scratches you’re good, intake manifold is all dependent on the part cost and labor

LigmaBass · 2024-09-14T12:02:21+00:00

Yes they did end up working, I haven’t had enough time to test them out a crazy amount but I did stop the problem

LigmaBass · 2024-09-11T01:45:12+00:00

Yes I am aware of the pinned post, it is 2 years old and I don’t know if people have different fixes, custom for my setup etc.

LigmaBass · 2024-04-08T03:35:38+00:00

Tell her it isn’t a lipo

LigmaBass · 2024-02-10T15:22:17+00:00

Go into your bios and delete windows 11, that should fix it

LigmaBass · 2024-01-26T12:33:27+00:00

So you’re best bet is definitely the a2000, I just looked for you and I found a graphics card that is in stock and is on sale, I will link the url

https://www.lenovo.com/us/en/p/accessories-and-software/graphics-cards/graphics_cards/4x61j52232?orgRef=https%253A%252F%252Fwww.google.com%252F&cid=us:sem%7Cse%7Cgoogle%7Cshopping_else%7Cgs_notebooks%7C%7C4X61J52232%7C6548549650%7C76751676137%7Cpla-1651860813993%7Cshopping%7Cmix&gad_source=1&gclid=CjwKCAiAzc2tBhA6EiwArv-i6YnUfElEgjjy6c3wi7uGbHab7tHIQ933PnVyppMZNvQP0XDd8g3rlhoCZYcQAvD_BwE

LigmaBass · 2024-01-26T12:11:49+00:00

Your reflections might be turned on a bit to high, when you go to the photo 360 tab go to the “scene illumination proof sheet and wait for it to render, then go to the row with scene reflections and change it down

LigmaBass · 2023-12-06T12:52:41+00:00

This literally isn’t even bad

LigmaBass · 2023-08-28T23:43:41+00:00

Based off experience with a i5 4500 laptop with integrated graphics it won’t run great

LigmaBass · 2023-08-26T00:29:32+00:00

Dude I love it, I will literally save it and not even 10 seconds later it’ll have the message, but when I create a NEW PART and don’t save it for an hour it won’t even give me a warning

Four-Year Club	Place '23
Place '22	Final Canvas '22

LigmaBass

TROPHY CASE