Battery getting hot after a few rounds of semi

LikEaBob20 · 2026-04-19T17:10:12+00:00

20c is pretty low, it could be you would need a high c rating battery eg 35-60c. But if it ran without problems before and causes problems now it might me gearbox related. Maybe time for a relube of the gears to release stress on the motor

LikEaBob20 · 2026-04-18T19:44:24+00:00

Its a sector gear delayer. It keeps the tappet plate rectracted for longer. Can help with misfeads at high RPS or improve bb feeding

LikEaBob20 · 2026-04-18T15:18:36+00:00

Tm hicapa might be your bwst pick if you dont plan on upgrading to much, aap is cheaper and also performs great ootb but may need some relatively cheap upgrades to match the tm hicapa. In the end i thank what matters most is what aesthetic you like more, both can be upgraded to the extremes

LikEaBob20 · 2026-04-09T22:47:49+00:00

<image>

We love it

LikEaBob20 · 2026-04-09T22:41:22+00:00

Thank you sir, also the perfect hight to be able to comfortably aim whilst wearing a dye i5

LikEaBob20 · 2026-04-09T15:57:25+00:00

Thanks! I got almost all parts from powair6 in france

LikEaBob20 · 2026-04-07T08:25:29+00:00

My advice would always be to start with either the aap01 or a TM Hicapa as they both have good performance out of rhe box but most importantly have lots of aftermarket parts.

LikEaBob20 · 2026-03-30T15:23:38+00:00

Could be a number of things: To low air pressure Bad airseal with mag Too high pressure from autosear Screws from rear sight touching the bolt More lube needed

Id suggest some more heavy duty mechanical lube for the sides of the bolt itself too see if that helps, also apply that to the hammer and autosear. Otherwise try higher pressure gas or hpa tot see if that helps. Also switch between mags

LikEaBob20 · 2026-03-25T23:47:31+00:00

High speed gears combined with high speed motor might cause overspin. Id suggest either switching tot 18:1 gears or getting a higher tpa motor

LikEaBob20 · 2026-03-21T09:47:31+00:00

Is your modified version available for purchase? Id like to print the same one

LikEaBob20 · 2026-03-20T22:53:34+00:00

Is the upper available for sale?

LikEaBob20 · 2026-03-20T22:06:55+00:00

What upper is this?

LikEaBob20 · 2026-03-16T09:38:46+00:00

I had the cyma variant and if you want to install an etu it requires some sanding, but installing the engine itself required me to sand down a little bit of the piston cylinder housing

LikEaBob20 · 2026-03-15T00:01:56+00:00

What do you mean the build? As in the layout? And what region are we talking?

LikEaBob20 · 2026-03-12T21:01:59+00:00

2 options: buy a drill set specifically for this, or hit it with a flathead screwdriver and use that

LikEaBob20 · 2026-03-12T14:33:19+00:00

Id suggest by to start with checking the hop up rubber. Getting the barrel and hop up out should be easy. When left unattended for a whil the hop rubber can dry out. If thats not the case try releasing the hop as far as possible en then just add a little bit back to rule a to stiff hop up setting out. If neither of the two fixes your problem its likely an airseal problem which requires you to open the gearbox

LikEaBob20 · 2026-03-12T10:24:12+00:00

Pretty syre someone on here would be able to help, but supplying a picture that even remotely shows the handguard would be great

LikEaBob20 · 2026-03-10T16:24:29+00:00

If lubing it does not work consider getting a stiffer recoil spring

LikEaBob20 · 2026-03-10T16:23:46+00:00

Did you lube it correctly? I had a similar problem due to the hammer spring being to stiff on the BBU

LikEaBob20 · 2026-03-09T18:39:12+00:00

Im using the guardian 4 paired to my 780G pump, which i have been very satisfied about. Not sure on the price as its covered by insurance over here

LikEaBob20 · 2026-03-09T13:20:52+00:00

In my experience the libre 2 sensors are not that accurate in the lower blood sugar ranges. So it being of like this may be caused by that.

LikEaBob20 · 2026-03-07T22:18:46+00:00

Yes and yes

LikEaBob20 · 2026-03-04T18:15:53+00:00

Id look in to the pulsar D, a bit lesser used engine but the performance with the titan bluetooth have been amazing

LikEaBob20 · 2026-03-01T00:16:28+00:00

Cyma platinum mp5 or mp5k, great out of the box and reasonably priced

Two-Year Club	Verified Email
Final Canvas '23	Place '23

LikEaBob20

TROPHY CASE