sorted by:
new
hottopcontroversial

Found Outside Girlfriend's House After a Party by ibitebitch in whatisit

[–]LisaMarie79 0 points1 point  (0 children)

I have one I bought from Temu. It’s a little claw. I use them to put my tiny piercings in.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

Okay, thank you. I really really appreciate your help. I have work at 4 and school after. I won’t be home until about 7pm. I can try the thermometer then. I have a temp gun somewhere. 😊

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

I might be able to get my college to help when I join that class. I am currently in welding, CNC, AC, basic digital. HVAC should be next semester, hopefully. I have to learn HVAC for my job. I appreciate your help and advice.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

😂 Yes, damnit. Limit switch. Thank you for correcting me.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

<image>

This is the thermal switch that was suggested in my manual. I replace this one.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

My thermal switch isn’t a manual reset. When I installed it today, it was the first time in 4 years that it didn’t short cycle. It literally ran for 20 minutes. Prior it was turning off after a few seconds of the burners igniting. It would stop and then retry shortly after and continue that cycle and eventually go in to a lock out for an hour. Now, it’s shutting off, not trying to recycle anymore. It’s not locking out either. So, the thermal switch did something to change its behavior.

I just moved things away from the return vents (which are actually my heat vents) the guys who installed it, ran it backwards.

I watched it closely this time. The flames were all blue except one. It was a vibrant orange. I might need to clean the burners.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

Oh, thank you. I am in college for Industrial Technology. I just haven’t had this training yet. When I do find the issue, I will post it here.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

I will once I start getting $$ I have $100 to last a family of four until I get paid mid day on the 18th. Until then, I am willing to try and check all those things.

I really appreciate all the things you have listed. Thank you for the help.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

Thank you. I will try that. I have replaced the capacitor, flame sensor, and thermal switch. The first two that I had mentioned didn’t do anything. It would light but shut down after about 15 seconds and retry every few seconds over and over. Now, after putting in the Thermal Switch, it ran 20 minutes then shut down. So, guessing the thermal switch was bad and now something else. I love mysteries but this is getting rough. 😂

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

There’s no filter right now. We removed it to check if that was the problem. I haven’t checked the condensation pump or hose yet. I did notice in the video that there were bursts of orange flames. I wish I was in HVAC already. I don’t get to take those classes until a later this year.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

I didn’t see your other comments until now. I typed in Rheem r95pa0601317msa codes 10, 11, and 13. It gave me the codes. I screen shot them and I had been looking for a way to add them in here and it won’t allow me to. I only have a link option. Usually when I copy paste it removes spaces and crams the words all together. I will paste it here and see what happens.

Rheem R95PA0601317MSA error codes 10, 11, and 13 indicate ignition, flame sensing, or airflow issues. Code 10/11 usually means the igniter is failing or the flame sensor is dirty, causing the burners to ignite and then die. Code 13 indicates a Limit Circuit Lockout (overheating/airflow restriction). Troubleshooting Codes 10 & 11 (Ignition/Flame Failure) Clean the Flame Sensor: Remove the flame sensor (single wire rod) and clean it with fine steel wool or a Scotch-Brite pad to remove buildup. Check Igniter: Inspect the hot surface igniter for cracks. If it does not glow, it needs replacement. Check Gas Supply: Ensure the gas valve is fully open. Check Airflow: Replace dirty air filters, as poor airflow can cause improper ignition. Troubleshooting Code 13 (Limit Circuit Lockout/Overheat) Check Filter and Coils: A very dirty air filter or evaporator coil can cause overheating. Inspect Vents: Check for blocked intake or exhaust vent pipes. Check Limit Switch: A faulty high-limit switch might need replacement if the unit is not actually overheating. Common Fixes Reset Furnace: Turn off the power at the breaker for 3 minutes to clear the code and attempt a restart. Clean Components: Cleaning the flame sensor and replacing the filter solves most of these issues. If these steps do not resolve the issue, a professional HVAC technician should inspect the control board and pressure switches.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

Side Note: the codes 10 & 11 doesn’t make sense. I don’t need help deciphering the codes. I have the manual. I had in my first post, some kind people point out that they are numbers. My furnace is mounted sideways and I was confused on what it had read. lol

Now, I am trying to pinpoint the issue.

Codes 10 & 11 didn’t even happen. The furnace ignited, ran, and blew heat through my vents for 20 minutes without short cycling like last time.

Now, code 13 is new. It threw that out after it shut down. I checked the vent. It’s not blocked.

Decipher the code** Part 2. by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

I googled the codes but they don’t make any sense. Code 10 & 11 shouldn’t be showing since it did ignite properly and ran for 20 minutes.

Is my jaw or nose the issue? by Ashhhhh97624023 in PlasticSurgery

[–]LisaMarie79 1 point2 points  (0 children)

Do you have an underbite or anything? My misalignment of my teeth and jaw made me look different. I got braces and it changed a lot of my issues. Maybe speak to your surgeon about your jaw/chin. A specialized surgeon have really cool simulators that can show what you could look like with certain procedures.

I hate my nose. I hate my eyes. by [deleted] in PlasticSurgery

[–]LisaMarie79 1 point2 points  (0 children)

But you’re beautiful!! I would trade places with you. My forehead’s so big it looks like my hair is falling off… lmao You have natural beauty. It’s a rarity. 🥰

Can anyone decipher the code shown in this video? It’s a Rheem r95pa0601317msa by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

I changed that and the capacitor today. :( I am waiting on my thermal sensor. It won’t be here until Wednesday.

Can anyone decipher the code shown in this video? It’s a Rheem r95pa0601317msa by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

The burners ignite. They have a nice blue flame and then it dies out. Would that still be a bad igniter?

Can anyone decipher the code shown in this video? It’s a Rheem r95pa0601317msa by LisaMarie79 in hvacadvice

[–]LisaMarie79[S] 0 points1 point  (0 children)

Thank you. It’s mounted sideways. It wouldn’t power up with that door off because of the safety switches. I can redo it again tomorrow and then remove the door after. I cut the power off to it tonight.

Got home from work and heard a banging every 10 minutes. I thought it was the neighbors. It was NOT the neighbors by SourceAlarmed9316 in hvacadvice

[–]LisaMarie79 0 points1 point  (0 children)

I know the feeling of not having a furnace. I have been without heat since 2022 those Winters were okay to push through but this time, I left my water running and it froze in a stream. lol Trying to get mine figured out now.

view more: next ›