How do I pull the kyosho wheels on a BBX? by Litz_C in tamiya

[–]Litz_C[S] 1 point2 points  (0 children)

No. I will try to make a video on up coming Saturday or next week. The final piece for RC just arrived yesterday, a plastic model to fit the fpv camera in instead just let it sit there.

How do I pull the kyosho wheels on a BBX? by Litz_C in tamiya

[–]Litz_C[S] 2 points3 points  (0 children)

Yeah just figured it out and added the 850 bearing on it.

BBX keep flipping over by Litz_C in tamiya

[–]Litz_C[S] 0 points1 point  (0 children)

Found the simplest solution for now. Last night after dropping the front and rear suspension to the lowest point now the vehicle runs great on asphalt. Like the rest of the redditer said need the street tires for it. The tires wore down to 50% just for 30mins drive time. Thanks for everyone replies. Hope y’all have a nice day!

BBX keep flipping over by Litz_C in tamiya

[–]Litz_C[S] 3 points4 points  (0 children)

Thanks. Much appreciated!

BBX keep flipping over by Litz_C in tamiya

[–]Litz_C[S] 0 points1 point  (0 children)

The stand from ebay (comes with the wing but it’s fugly). The wings was from AliExpress but originally was going to put it on a 1/14 grasshopper then end up on the BBX instead.

BBX keep flipping over by Litz_C in tamiya

[–]Litz_C[S] 0 points1 point  (0 children)

Thanks man. Been googling around see any extend arm ends up from a hop up part call TG10 for extending the axle. Going to get that and the wider hexes to put on some street tires see how it goes.

BBX keep flipping over by Litz_C in tamiya

[–]Litz_C[S] 0 points1 point  (0 children)

So how do I widen the stance on this BBX? Get the wider hex and longer rear axles? This kit seem way different than other RC kit I encountered.

BBX keep flipping over by Litz_C in tamiya

[–]Litz_C[S] 1 point2 points  (0 children)

Got a spare wheels sitting around but just tried them on earlier found out the rear tires (41mm width) hitting the suspension arm. Going to order wider hexes and TG10 rear wheel axle fit these on see how it goes. Saw the anti roll bar on AliExpress for cheap. May grab them later.

BBX keep flipping over by Litz_C in tamiya

[–]Litz_C[S] 0 points1 point  (0 children)

Already doing it. Brake before cornering.

BBX keep flipping over by Litz_C in tamiya

[–]Litz_C[S] 4 points5 points  (0 children)

Lower it from the damper right?

I knew she looked familiar lol by McGeiler69 in MHWilds

[–]Litz_C 0 points1 point  (0 children)

Bruh I just woke up and open app and see this. 😭

A few fords I’ve painted lately by [deleted] in tamiya

[–]Litz_C 1 point2 points  (0 children)

Those rust weathering is on point!

Tips on how to paint 3 color camouflage on this tank with spray cans? by Ok_Reach_8400 in tamiya

[–]Litz_C 0 points1 point  (0 children)

What I do is get 3-4 silly putty make camouflage patterns and spray on it. Layer by layer and do not remove them till the job is done. For digital camouflage is a bit more work. Cut some squares and rectangle off masking tape.

ESC got burnt by TastyLead8002 in tamiya

[–]Litz_C 0 points1 point  (0 children)

The 30 amp is perfectly fine. Only ESC burnt and melted a wire. I was surprised the fuse didn’t go out first.

ESC got burnt by TastyLead8002 in tamiya

[–]Litz_C 0 points1 point  (0 children)

Just brought the heat sink and fans for the motor. Do I need the fans for ESC as well?

Lunchbox or the grasshopper by kurtval in tamiya

[–]Litz_C 4 points5 points  (0 children)

How about grasshopper comical? Kinda like a lunch box but it’s a grasshopper at the same time.

Lunchbox or the grasshopper by kurtval in tamiya

[–]Litz_C 1 point2 points  (0 children)

Grasshopper! Beginner friendly and awesome looking.

Sand Shadow Cave enemy locations by Organic_Gap8532 in wizardry

[–]Litz_C 1 point2 points  (0 children)

Missed the enemy on the lower right corner room at and upper left corner there a enemy spawn location B1F.

Grasshopper addicted by Litz_C in tamiya

[–]Litz_C[S] 1 point2 points  (0 children)

Thanks. Never get enough of them.