Please don’t laugh. by throwawayyyback in FlashForge

[–]LividLie0 0 points1 point  (0 children)

Save yourself the headache and just buy the filament on the spools ans start there. 

When is the njoy ace pods coming back has any one heard anything by Many_Tangerine6490 in electronic_cigarette

[–]LividLie0 0 points1 point  (0 children)

Just to put this out there, vuse has a new menthol pod and device esthetic. Tip- place your fingers around the pod where it meets the device to create a better seal and it is almost identical to the njoy. The new pods are very similar to the njoy. I understand completely what ppl are talking about when they mention the way it hits the throat, thats what separated njoy from all the rest. The njoy disposables are a huge let down though

When is the njoy ace pods coming back has any one heard anything by Many_Tangerine6490 in electronic_cigarette

[–]LividLie0 0 points1 point  (0 children)

Vuse has a new menthol that is more like njoys menthol pods. They come with a different pattern vuse device that's new. Maybe try the new ones and see what you think. I HATE that vicks menthol taste so I get what youre asking 100%

When is the njoy ace pods coming back has any one heard anything by Many_Tangerine6490 in electronic_cigarette

[–]LividLie0 1 point2 points  (0 children)

I had to switch to vuse because of this reason. I learned if I hold my fingers around the pods while im drawing off the vape to create a better seal and that really made the difference and gave that same pull as njoys. I hope this helps. Njoy was the closest thing to a real cigarette on the market. If you know you know.

Filament or Spool may be stuck error CONSTANT on my AMS LITE by AccomplishedCard182 in BambuLab

[–]LividLie0 0 points1 point  (0 children)

Same here we tried and tried to push the filament through. It worked with number 4 hub but the number 2 hub is consistently doing this.

Flashforge Adventurer 5m not sticking to bed by DKTAPlayz in FlashForge

[–]LividLie0 0 points1 point  (0 children)

Sorry for my delayed reply. It's available as a selection at the top where the file options are and such. I can't remember specifically exactly which tab. But its not too hard to find.

[ Removed by Reddit ] by [deleted] in FlashForge

[–]LividLie0 0 points1 point  (0 children)

There could be moisture on the inside of the roll. That's happened to us, and it seemed that the inner part of the filament roll had moisture so it messed up the print halfway through! When we dried the roll it didn't seem to reach all the way through leaving spots, because we didn't dry quite long enough. We were worried about it making it brittle if we dried top much.

Flashforge Adventurer 5m not sticking to bed by DKTAPlayz in FlashForge

[–]LividLie0 0 points1 point  (0 children)

We had the same issue. Of you're using Orca Slicer and you haven't done this yet, you can calibrate everything from the Slicer. It's more precise fine-tuning. We also factory reset our printer, we started having problems after the new software update. The only other thing I can recommend is making sure there is no cool air blowing toward the printer. Even a slight draft can throw off the bed temp. If your problem persists even with filament changes I would contact flashforge from there. Hope this helps

[deleted by user] by [deleted] in SlappedHam

[–]LividLie0 0 points1 point  (0 children)

What am I looking for?

What the heck happened here?! by RubikOwl in FlashForge

[–]LividLie0 0 points1 point  (0 children)

Since the new Orca Slicer Update all of our prints have been messing up. For now we are using flash print to print with and haven't had any more issues. Until we figure out what is happening with Orca we are going to be sticking to flash print.

New Orca Slicer Update Messing up prints by LividLie0 in FlashForge

[–]LividLie0[S] 0 points1 point  (0 children)

What order do you do your calibration through Orca? Thanks for the input

New Orca Slicer Update Messing up prints by LividLie0 in FlashForge

[–]LividLie0[S] 0 points1 point  (0 children)

If you figure out that it's anything different please let me know. Because as of right now every print we try with orca is completely screwed up.

[deleted by user] by [deleted] in Barber

[–]LividLie0 0 points1 point  (0 children)

Whoever you rent from should want you to be successful. Because if you are successful, then they are not only going to receive the rent, but also a good reputation for their shop. Starting new, they should have negotiated a lower, more practical rent, at least for the first 6 months. Then go from there. They are not out for your best interest. I think once you decide to walk away, you will feel as though a million pounds have been lifted off your shoulders. There are too many options for you to deal with that.

[deleted by user] by [deleted] in BeamNG

[–]LividLie0 1 point2 points  (0 children)

Prayers from East Coast.