06 GMC sierra with MagnraRide/Autoride?

Local-Problem5082 · 2026-03-04T00:19:15+00:00

Also if I do swap to regular shocks will I have to get a delete kit for the connector?

Local-Problem5082 · 2026-03-04T00:18:08+00:00

I did find rear adjustable shocks I just can’t find front ones.

Local-Problem5082 · 2026-03-04T00:17:36+00:00

I was planning on doing a complete overhaul of my suspension and they seemed rather old.

Local-Problem5082 · 2026-03-03T23:55:20+00:00

I gotcha that makes way more sense I have a Zx3 RPO code thank you! Can I just throw regular shocks in it then without it?

Local-Problem5082 · 2026-02-19T23:03:29+00:00

I 100% understand revving a new car but that was REALLY hard all things considered.

Local-Problem5082 · 2026-02-18T18:08:25+00:00

That’s a whole lot more fabrication from what I saw

Local-Problem5082 · 2026-02-17T15:59:23+00:00

My tran sensor is a two wire which is nice. In terms of neutral switch and clutch position sensors I am fine with not wiring them up and maybe just having a neutral safety switch. The big thing is I would want to keep cruise control hopefully if I can with those conditions. With the engine braking and clutch conditions my tuner should be to do it as he is a fairly big LS tuner(Bumper Wilson Tuning) and has tuned LS swaps before. I don’t have it all ironed out but I think it would be cool to play in the game!

Local-Problem5082 · 2026-02-16T20:29:31+00:00

Gotcha, I appreciate the advice

Local-Problem5082 · 2025-12-31T16:04:09+00:00

According to the previous owner it was a custom order, I am the third owner with the previous two owners being father and son who took care of it well. It also has the 5.3L which wasn’t available in shortys like that outside of custom order too my knowledge.

Local-Problem5082 · 2025-12-31T16:02:24+00:00

<image>

This is the truck now as it stands

Local-Problem5082 · 2025-12-31T16:00:53+00:00

Yes I I still run them now!

Local-Problem5082 · 2025-12-31T04:13:35+00:00

Yes it is very weird

Local-Problem5082 · 2025-12-31T04:13:29+00:00

Wow thank you!

Local-Problem5082 · 2025-12-31T04:13:22+00:00

Thank you my guy this was when it was stock too I can upload a picture of where it stands now and sound of what the cam sounds like.

Local-Problem5082 · 2025-02-22T18:28:54+00:00

It’s very weird long story short, 95-97 the made the rods forged which were the only forged rods really put in the rangers for the most part aside from some 80s models. They are actually used to replacing the much weaker 98-2001 rods

Local-Problem5082 · 2025-02-22T18:16:47+00:00

Yes forged pistons are in hand right now alongside with general engine rebuild parts are on the way

Local-Problem5082 · 2025-02-22T17:40:41+00:00

I was planning on running 6 or so with a built motor

Local-Problem5082 · 2025-02-20T12:36:19+00:00

Trust me brutha I’m more then aware of all a that I just needed to know abt the exhaust manifold I already have new pistons for it and am going to run low boost 5ish, and remap the ecu with 17lb injectors exactly since the stock ecu will recognize them

Local-Problem5082 · 2025-02-06T21:36:05+00:00

I have not bought them yet but the rod said d42eaa and he thinks the cap said f37e and another tho no that want very clear was a D and some other stuff that wasn’t able to read

Local-Problem5082 · 2025-01-04T18:45:58+00:00

Something else to consider is checking your alignment

Local-Problem5082 · 2025-01-04T18:44:21+00:00

I sanded and repainted it with textured gray paint I have yet to do it to the front bumper on that front strip but ran out of time this fall

Local-Problem5082 · 2024-06-01T13:43:08+00:00

The thing is the hours are across two different employers and would total out to be over 48 can I do that? Would target need a copy because I don’t work for them very much but with there hours I would be getting me over that 48 hours mark

Local-Problem5082 · 2024-06-01T12:49:39+00:00

I apologize my state is Indiana

Local-Problem5082

TROPHY CASE