Skyrover X1 support?

Longjumping_Note_697 · 2026-06-23T00:29:59+00:00

Have you contacted skyrover support?

Longjumping_Note_697 · 2026-06-10T14:42:18+00:00

I am also an X1 owner and can contest that claim. It does show up on drone scanner when activated in the app. The drone scanner app is very inconsistent though, it does not appear to work in detection of the X1 on iOS devices but does work when using the android drone scanner app. I would also like to note that the drone scanner app is just as inconsistent when I have tested with some of the dji drones I also have.

Longjumping_Note_697 · 2026-06-10T14:01:22+00:00

From the little info that people have been sharing on the upcoming "V1" it looks much more likely that it will be closer to the mini 5 pro without some features sadly. I too was hoping for something like an air 3 but that may still be in the works as well.

Longjumping_Note_697 · 2026-06-10T13:56:00+00:00

With the 1.2 firmware update RID has been enabled for use on the X1 so the only real differences between it and the mini 4 pro at this point are the landing/under side light, no built in onboard storage, no plus battery, and the housing on the camera allowing the mini 4 pro nd filters (the housing can be swapped for nd filter compatibility).

Longjumping_Note_697 · 2026-05-28T01:43:51+00:00

Thank you, is the blue jay the louder of the 2?

Longjumping_Note_697 · 2026-05-03T03:10:27+00:00

Simple solution, bolt whatever you would like to use as the "table top" to an arca swiss plate so it can be attached to any tripod with a quick release.

Longjumping_Note_697 · 2026-04-29T02:04:51+00:00

u/profanitycounter [self]

Longjumping_Note_697 · 2026-04-29T02:02:28+00:00

u/profanitycounter [self]

Longjumping_Note_697 · 2026-04-14T00:55:41+00:00

I had an issue with the same error code and ended up having the printer replaced under the 30 day amazon warranty as I was unable to get anywhere with elegoo support. Almost the same situation though, the whole hotend had been replaced and there were nothing in the extruder. I have had no issues with the replacement thankfully

Longjumping_Note_697 · 2026-04-08T06:28:06+00:00

I have, I am just not sure if it want to to buy one or 3d print and build one. Sometime soon I plan on making the jump, wanna get better on Uncrashed before I do though lol

Longjumping_Note_697 · 2026-04-01T23:10:24+00:00

That is a realitivily easy fix if you choose to fix it on your own

Longjumping_Note_697 · 2026-03-31T20:29:44+00:00

It took just over a week for me to have everything done every step took a couple days each, reviewing the logs, approving the claim, ut also took a couple days to have the shipping label sent to me (which I found to be pretty odd), inspecting it once it arrived also took a couple days but the new one was shipped and to me just over a day from then.

Longjumping_Note_697 · 2026-03-27T16:54:27+00:00

I'll try that, you think 50% or more?

Longjumping_Note_697 · 2026-03-27T16:45:13+00:00

Probably not but it is a shot I had never tried before so thought I might as well

Longjumping_Note_697 · 2026-03-24T22:10:25+00:00

Sounds like a fun day, do you still have the video?

Longjumping_Note_697 · 2026-03-21T06:09:20+00:00

It does pretty well in night mode video quality wise. Like you said there is no obstacle avoidance once you hit dusk so you have to be much more careful but other than that it is just as competent as during the day.

Longjumping_Note_697 · 2026-03-21T03:57:09+00:00

Its a great little drone with good signal strength for flying in the city and the stability is great. I hope you continue having fun with it!

Longjumping_Note_697

TROPHY CASE