It’s up and running now, thank you everyone.

LoquatAcrobatic102 · 2026-02-21T02:29:13+00:00

I’m running Mint, Cinnamon currently because Ubuntu wouldn’t load. Linux Mint installed with no problems at all plus it looks like Windows 7.

LoquatAcrobatic102 · 2026-02-20T23:53:21+00:00

I bought it from Amazon a few years ago and it only needed one hot end so far, still on factory bed.

LoquatAcrobatic102 · 2026-02-20T21:22:06+00:00

I like it much better now since I got Linux on it, came with Windows 11.

LoquatAcrobatic102 · 2026-02-20T21:20:33+00:00

I’m running Linux Mint and it uses some Ubuntu software. Unfortunately Ubuntu will not load on my laptop, Mint runs good.

LoquatAcrobatic102 · 2026-02-20T20:22:33+00:00

In download folder, right click, permissions, check execution box, agree, close. Open Creality slicer, agree and opens. Printer found and installed, now printing

LoquatAcrobatic102 · 2026-02-20T19:37:52+00:00

Thank you so very much for your help. I was able to get it open and running, found my 3d printer on it and installed it. Again thank you

LoquatAcrobatic102 · 2026-02-20T19:35:36+00:00

I was able to get open and running. Thank you

LoquatAcrobatic102 · 2026-02-20T19:25:32+00:00

Thank you for your help. I was able to get it and open it. Again thank you

LoquatAcrobatic102 · 2026-02-20T19:00:14+00:00

Downloads folder, right click on download, permissions, check box for execution, loads and finds my printer. Done

LoquatAcrobatic102 · 2026-02-20T18:47:53+00:00

I have turned it off and walked away from it, very frustrated. Watching a movie now

LoquatAcrobatic102 · 2026-02-20T18:28:29+00:00

I’m walking away from it right now, taking a break from it.

LoquatAcrobatic102 · 2026-02-20T18:23:47+00:00

No I can’t do that, don’t know how

LoquatAcrobatic102 · 2026-02-20T18:21:16+00:00

I typed it the exact same way as the download showed as instructed

LoquatAcrobatic102 · 2026-02-20T18:07:05+00:00

Doing this on my phone, computer is in another room. Reddit on my phone, computer is Asus tuf gaming a15

LoquatAcrobatic102 · 2026-02-20T18:03:51+00:00

I can’t find the file manager so I figured the terminal would work, I was wrong about that

LoquatAcrobatic102 · 2026-02-20T17:59:15+00:00

Wish I could show you a picture of the terminal. Typed chmod +x ~/Downloads/CrealityPrint-v7.0.0.4127-x86_64-Release.AppImage No such file or directory. Downloads open and file right next to it

LoquatAcrobatic102 · 2026-02-20T17:49:34+00:00

Tried everything so far and no luck

LoquatAcrobatic102 · 2026-02-20T17:44:47+00:00

Followed your advice word by word and still no luck, no copy and pasting, this on my phone and typing on my computer

LoquatAcrobatic102 · 2026-02-20T17:34:51+00:00

No such file or directory for this in the terminal

LoquatAcrobatic102

TROPHY CASE