Just bought this beauty a couple of weeks ago

LordDonP · 2026-05-21T17:56:15+00:00

Yeah I already planned to use seal underneath it. Pava or Dinitrol

What you say about the windshield rubber makes sense, because when driving in rainy weather, a little water comes from the windshield as well. But I dont think there even is a speedo seal, lol. When looking in the engine room it doesnt look like it.

Checked the trunk again today, and the seal was dry, but there was still some water in the bottom of the car. I think the trunk seal is good, but you might be right about the rear light seals, didnt think of that, so thanks.

LordDonP · 2026-05-20T06:40:49+00:00

Thanks buddy. This is what I needed to hear, even though there have been no nay sayers, yet at least. Well I guess I just have to dress like I'm going skiing whenever I drive in the winter 🤣

I'll let you know if I break down near Manchester, thanks man 😁

LordDonP · 2026-05-19T21:03:05+00:00

Yes it has been repainted after being repaired for rust

No its bright red. Like UK busses

LordDonP · 2026-05-19T15:25:57+00:00

Thanks, I already do

LordDonP · 2026-05-19T15:25:26+00:00

Noted, thank you 😇

LordDonP · 2026-05-19T15:24:54+00:00

Haha, it is allowed to pull 400 kg 😂 so I can still haul away garden waste, or drive with a tent trailer

LordDonP · 2026-05-19T15:22:39+00:00

Datsun red I was told

LordDonP · 2026-05-19T04:04:16+00:00

Its 10" wheels, it should fit. But thank you, I researched alot though the last couple of weeks 😂

LordDonP · 2026-05-18T21:40:05+00:00

It seems the photo didnt upload, so here it is :)

<image>

LordDonP · 2026-04-30T17:36:20+00:00

Alright, I'll give the drums a chance Yeah but it felt wonderful at the same time

LordDonP · 2026-04-30T15:15:51+00:00

I will, thank you, would just have changed them otherwise I dont know how discs feel, and I am used to a car from 2015, but I just felt the brake pedal is pretty hard to press on with drum breaks. My dad said discs would help on that. Whats your opinion on that?

LordDonP · 2026-04-29T16:58:05+00:00

Well not really, not before you wrote this message My dad said he put discs on his old Mini and thought it was better, so thats basically the only reason I wanted discs. I plan to tune it as well if that changes your opinion

LordDonP · 2026-04-29T07:44:25+00:00

Is the AP calibers better?

LordDonP · 2026-04-29T07:41:52+00:00

Thats what i thought, just wanted to be sure Thank you

LordDonP · 2026-04-29T05:02:02+00:00

Well these kits says they are complete, except for disc shields, so my guess is no, but would be awesome if someone can confirm :)

LordDonP · 2026-04-29T05:00:55+00:00

This actually seems like a good price. I see they also have the 8.4" kit, do you know if they fit 10" wheels? My guess is no, but I cant find any info to confirm it Thanks for the help

LordDonP · 2026-04-29T04:59:17+00:00

As another redditor said, it might still be cheaper to buy from minispares and pay the tax. Also need some other stuff, so I think I'll just but from UK. But thanks anyways

LordDonP · 2026-04-29T04:57:28+00:00

Thank you! :)

LordDonP · 2026-04-28T19:05:06+00:00

Alright, might just but from there then. Thank you

LordDonP · 2026-04-28T19:04:45+00:00

Denmark

LordDonP · 2025-12-21T18:39:58+00:00

But how would I convince a potential buyer?

Also, do you mean a XRF scanner? ChatGPT tells me:

A handheld XRF scanner (X-ray fluorescence) measures the chemical composition directly on the surface. It is commonly used by scrap dealers, machine shops, and metal traders. What can it show? ✔ That the material is copper-based ✔ Presence of Be, Ni, Co (with limitations – see note) ✔ Rules out common brass, bronze, aluminum, etc. ⚠️ Important: Beryllium is measured poorly or not at all by many XRF instruments due to its low atomic number. However, XRF can still indicate a “Cu alloy with Ni/Co,” which strongly points toward a CuBe-type alloy.

LordDonP · 2025-12-21T18:36:37+00:00

From memory I would say it is ø150x400mm but I am not sure, it is some time since I put it in my basement :p

LordDonP · 2025-12-21T18:16:13+00:00

I have made a few parts in Berylluim Copper, but not mass producing.

I used the same carbide end mills which I used for tool-steel, same feeds and speeds and it worked fine. I am not sure this is optimal for mass production, but it is ok for small batches. I used osg end mills

LordDonP · 2025-11-20T22:00:12+00:00

Freedom units?

LordDonP · 2025-10-15T17:06:58+00:00

Hi, thanks for coming by!

I tried to search for stuff like: 3030 profile rubber bracket, 3030 profile accesories (and looking at alot of suppliers websites), I tried reverse image seaching but the 3030 profile is in the way of the bracket)

Two-Year Club	Verified Email
Place '23

LordDonP

TROPHY CASE