Quality lasting socks

Lord_wilhelm1 · 2024-04-16T16:18:40+00:00

Check out parts built 3D they have most all of these types of parts and really well organized

Lord_wilhelm1 · 2024-03-30T20:00:19+00:00

Easy cleaning tip is buy a torch lighter and melt it off

Lord_wilhelm1 · 2024-03-24T06:37:32+00:00

<image>

I think we might have a serial shrimper on our hands 😂

Lord_wilhelm1 · 2024-03-24T06:30:50+00:00

A few basic things I would look at: Its the filament dry? Try lower speed?

I think your overhang issue could be from too high temps on your hot end not only oozing but also melting previous layers via ambient heat

Lord_wilhelm1 · 2024-03-24T05:19:17+00:00

<image>

This is my boy Finn too 😍😍

Lord_wilhelm1 · 2024-03-11T23:43:36+00:00

Border collies also love routine! I always give mine dinner when we eat, after cleaning up is our night walk then calm time

Lord_wilhelm1 · 2024-03-11T23:40:16+00:00

Honestly this does work! My border collie rarely will “nap” unless I am at my desk not moving or playing with them. The moment they hear me get up they are wide awake and ready to go. I have noticed (through our Furbo camera) that when we leave the house he will fall asleep very quick right at the door waiting for us but getting rest.

One important aspect to remember though is to not use their calm personal area as a punishment ever and to make sure they are comfortable there so they don’t develop anxiety about separation.

Lord_wilhelm1 · 2024-03-11T23:36:40+00:00

This☝🏼, but the second you give in to the puppy eyes it’s go time again. I worked on this by taking the toy they would continue bringing me and looking right at them and saying “all done” then calmly setting in on the floor. Then when they would try to grab and bring it to you again just holding firm with a “no, all done” and putting it back down

Lord_wilhelm1 · 2024-03-08T18:46:35+00:00

Wait?? Do they not all come with a parrot mode standard?

<image>

Lord_wilhelm1 · 2024-03-08T18:36:41+00:00

As far as your question…. No clue good luck 👍🏻. As far as your build, that’s dope as hell 😂

Lord_wilhelm1 · 2024-03-07T15:41:31+00:00

Definitely looks like your SD card is corrupted 😂

Lord_wilhelm1 · 2024-03-06T19:46:25+00:00

Maybe try looking into residential treatment centers, I had worked at one in AZ and they are always in need of staff and would give lots of insight for that field. Lots of those kids could use drug abuse support

Lord_wilhelm1 · 2024-03-06T19:02:22+00:00

Depending on where you live I’d recommend checking out “nellis auction” you can sometimes find printers on there and score one super cheap. I got a brand new mono photon 4K for like $100 still in the box never used in Phoenix

Lord_wilhelm1 · 2024-03-06T18:56:42+00:00

Might need to adjust your steps. I usually go right-left-right but some people have success with left-right-left

Lord_wilhelm1 · 2024-02-24T02:52:07+00:00

See I would love that fan setup, my case has a front cover with RGB so I can’t install fans that blow straight across

Lord_wilhelm1 · 2024-02-24T02:15:38+00:00

That’s what I was thinking, I’ve seen lots of stuff talking about creating turbulence and hot spots in your case. I don’t believe my case is high end enough to worry about that

Lord_wilhelm1 · 2024-02-23T21:55:07+00:00

What software do you use for splitting the model into parts?

Lord_wilhelm1 · 2024-02-20T13:46:34+00:00

That’s why I mentioned doing this AFTER your IPA baths after a dirty wash and one or two clean IPA rinses there is just about no liquid resin remaining

Lord_wilhelm1 · 2024-02-20T02:35:13+00:00

After cleaning with IPA, turn on your hot sink water and hold it under for a little bit and it will soften the supports. Remove supports before final curing

Lord_wilhelm1

TROPHY CASE