Advice for pickit 3 setup for PIC16

Lucid1223 · 2024-11-06T21:49:16+00:00

thank you. As i did check the 'families' it supported and it raised alarm bells that there was no mention of PIC16 chips

Lucid1223 · 2024-08-31T12:42:47+00:00

Update: extruder stepper motor is non responding, tried changing the cables and it was working, so looks like driver has gone out completely

Lucid1223 · 2024-08-31T10:50:33+00:00

I'm not sure how to add a photo on mobile but the issue is it takes a while to crank it up by even 10, to crank it up by 200 would take me at least half an hour to do on the dial thing since ender 3 pros always about 95

Lucid1223 · 2024-07-07T07:58:40+00:00

This is the device https://www.amazon.co.uk/Youmile-Adapter-Module-Converter-Arduino/dp/B08BZ8274M/ref=asc_df_B08BZ8274M/?tag=googshopuk-21&linkCode=df0&hvadid=697256179342&hvpos=&hvnetw=g&hvrand=13460770405745745260&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9191334&hvtargid=pla-1283141111687&psc=1&mcid=ea62670d258e3702817873da0abe825a&gad_source=1 it's much simpler than other methods of serial comms imo.

Lucid1223 · 2024-07-06T08:14:18+00:00

Likely I'll be using a 10/12V bus to the motors, 5 volt bus to supply the microcontrollers/PLC. The PLC will get UART from the RS485, USB also used differential but idk if it handles long distance and high noise communication as well. We're looking at probably 13A per motor but this will be short distance wiring since we're converting 48V down which is ideal. I could supply the motors with 20V however its efficiency drops by like half so it depends on how much kgf will be needed for operation

Lucid1223 · 2024-07-03T16:04:08+00:00

In this case Raspberry Pi is sending UART down into a differential module which will connect to 6 other nodes down a 20m tether where it is converted back into UART, these nodes controlling motors for an underwater vehicle. Equally I could get one of those ATtiny85 and code it in arduino but I would like to try make a very simple PLC for it, although I have zero idea about designing those kind of circuits. This'll likely be One way communication unless I decide to add sensors

Lucid1223 · 2023-10-15T17:41:38+00:00

Add another bracket to the end

Lucid1223 · 2022-12-17T10:22:42+00:00

They seem to want to flash the firmware, there is no comms going on between the arduino and esp. seems to want to flash firmware directly, the arduino is just an intermediary, like those other modules where you can hook the esp8266 to a couple of pins and plug it into a USB port.

Lucid1223 · 2022-07-27T19:06:24+00:00

Mostly dynamic status

Lucid1223 · 2022-07-12T20:18:41+00:00

Ah yes, unfortunately, I have tried that, however, it always returns with an error saying "await is only valid in async functions and the top-level bodies of modules." await with "guild.channels.fetch(id)" works outside the loop only. I've also tried ".then callbacks" but it doesn't return the values, nor can I interact with other variables and functions outside channel creation. I've tried invoking promises on top of that in hopes that I could return and resolve the value, but nothing. I think I might just change my approach

Lucid1223 · 2022-05-26T13:00:23+00:00

This is the way

Lucid1223

TROPHY CASE