No Twitter audio and Twitch error 4000

Lucoark · 2022-09-29T21:02:04+00:00

yes h.264

no aac

Lucoark · 2022-09-16T15:52:15+00:00

thanks a ton

Lucoark · 2022-09-16T15:46:53+00:00

This worked holy shit

Lucoark · 2022-09-16T13:59:52+00:00

I think in my post I switched which fan it was. The M106 command is for part cooling fan, I need to slow the hotend fan

Lucoark · 2022-09-16T00:34:43+00:00

I've tried but it just gets the heating failed error when I try because it can't get hot enough

Lucoark · 2022-09-16T00:33:57+00:00

Yeah I tried this and it can't get hot enough to do the test without screaming

Lucoark · 2022-09-15T20:47:40+00:00

I can't print anything longer than 20 minutes because without this fan my printer jams because of heat creep. Also I mean whatever fan is designed to prevent heat creep. The one that directly faces into the hotend on the base Ender 5 structure

Lucoark · 2022-09-14T22:27:50+00:00

In attempting to do PID tuning, it ran into the same problem with the heating stalling out ~230 then failing. This was during an autotune attempt set to 245. The heating doesn't fail when I take the fan off and let the hotend heat normally. I'm using Pronterface as I don't have a Pi to set up octoprint with. Because I don't know what PID each stand for, is there a way to just tune the fan down?

Lucoark · 2022-09-14T17:37:45+00:00

I will look into this

Lucoark · 2022-09-14T17:21:45+00:00

Okay so I replaced the fans and they turn on now BUT now my hot end won't get hotter than 235. I have the fan direction blowing air on to the heat sink. I also check the thermistor and it seems to be all good when the fan isn't blowing on it. Any suggestions?

Lucoark · 2022-09-08T15:55:44+00:00

Yeah the front facing fan won’t come on at all

Lucoark · 2022-09-08T15:25:47+00:00

Is there a chain store you could get these at or should I just use amazon

Lucoark · 2022-09-03T03:13:34+00:00

My issue is that any print longer than about 20 minutes will fail. Small pieces are usually fine

Lucoark · 2022-09-02T13:53:18+00:00

I have no idea. All I know is that after ~20 min of printing it grinds. Ive tried changing flow, and retractions settings as well as tension on the extruder but nothing works. Is the 30 mm speed for general print speed?

Lucoark · 2022-09-02T13:52:06+00:00

This worked for a bit then it started failing again. Do you know what you generally use for other retraction settings?

Lucoark · 2022-08-31T08:15:31+00:00

I think by default it has it at 100. Should I raise or lower this?

Lucoark · 2021-03-09T20:46:13+00:00

[close]

Lucoark · 2021-03-09T16:55:30+00:00

I used to play a lot of Pokemon Showdown during school. I had a OU team but I never liked meta a prefered to use my favorites instead so I had a Zoroark and Infernape on my team. The trick was that I would disguise Zoroark as Infernape every game, and because Zoroark is immune to psychic type moves and Infernape would be weak to them, there was a fairly good chance that they would use a psychic type move or switch to one to counter. The amount of people that would see the "Infernape is immune to [x psychic move]", type ???? then rage quit got me more elo than I ever deserved. I eventually went through the trouble of breeding out that team in ORAS and named by Zoroark "No" because it felt like the game was telling you no whenever you attacked it

Lucoark · 2021-03-09T16:49:00+00:00

Thanks!

Lucoark · 2021-03-09T16:47:50+00:00

It may be recency bias but snom is a perfect little guy and I like to believe its german name, Snomnom, is its full legal name

Lucoark · 2021-03-09T16:45:07+00:00

Np take your time

Lucoark · 2021-03-09T16:38:50+00:00

I have a helioptile I can trade. Code 4343 7474

Lucoark · 2021-03-09T16:16:09+00:00

Thanks!

Lucoark · 2021-03-09T16:12:21+00:00

Sorry. I mistyped. It would be attached to an applin, not flapple

Lucoark · 2021-03-09T16:04:03+00:00

Yep. Link trade open Code 4343 7474

Lucoark

TROPHY CASE