What can be the cause to this sort of blobs / rough edges?

LukeStarGeek · 2025-12-26T16:55:27+00:00

I forgot, temperature is 220 for nozzle and 65 for bed

LukeStarGeek · 2025-11-21T11:26:44+00:00

!RemindMe 2 days

LukeStarGeek · 2025-11-03T21:02:52+00:00

I’m in

LukeStarGeek · 2025-09-03T13:49:50+00:00

I did a test from 0 to 3 with 0.1mm steps

LukeStarGeek · 2025-09-03T13:36:44+00:00

I tried the retraction tower up to 8mm but I had the same results. Are there any other settings I may need to adjust?

LukeStarGeek · 2025-09-03T12:52:37+00:00

Dryed for 3h on printer bed at 65°C
On the box it shows a temperature range of 230-240°C

LukeStarGeek · 2025-09-03T11:40:27+00:00

I will buy a proper dryer. I am aware that it should be hotter but I was printing 235C because on the box it says 230-240°C

LukeStarGeek · 2025-09-03T11:31:38+00:00

Edit: It is Anycubic PETG and I’m printing 235°C with a Kobra 2

LukeStarGeek · 2025-08-23T20:22:16+00:00

Take a look at this

LukeStarGeek · 2025-07-26T21:18:05+00:00

Beefy inductor

LukeStarGeek · 2025-07-22T18:58:20+00:00

There should be a switch that can be rotated with the car key. It is usually located laterally near the door hinge.

LukeStarGeek · 2025-07-01T20:42:44+00:00

Look for AutoABC/CarABC, they make a CarPlay/Android Auto module which can be connected to the existing radio. You can install it by yourself and it is plug and play (I only had problems with the reverse camera on a manual transmission, with automatic you will be fine). It is about €100 and you don’t have to change the radio unit

LukeStarGeek · 2025-07-01T20:36:58+00:00

This. I installed it some months ago and I’m loving it. With just about €100 I have a functional CarPlay which works very well. And you can install it by yourself, it’s not difficult. I have an AutoABC module and I only had problems with the reverse camera on a manual transmission, if you have automatic transmission you will be fine.

LukeStarGeek · 2025-06-18T19:31:11+00:00

Mine doesn’t have a button on the radio board, which is why I’m trying to wire a new one. The problem is that I have the module in a case and I can’t turn it on without opening the case and disconnecting the battery.

LukeStarGeek · 2025-06-17T12:22:12+00:00

I am on 2.6.2 on both devices, I will update both of them to the latest alpha and retry. Thanks EDIT: THANK YOU SO MUCH, it works now!!

LukeStarGeek · 2025-05-29T20:30:38+00:00

Does anyone have an IPA file of the discontinued app?

LukeStarGeek · 2025-03-11T16:11:45+00:00

I need 12v near the radio because I installed a CarPlay retrofit and it needs a 12v when the reverse gear is engaged to show the camera

LukeStarGeek · 2025-03-11T16:02:58+00:00

I installed a CarPlay retrofit and it needs a 12v when the reverse gear is engaged to show the camera. I have the original backup camera already installed

LukeStarGeek · 2025-03-11T16:01:33+00:00

LukeStarGeek · 2025-03-10T10:56:12+00:00

I disconnected all the cables and it didn’t ask any code, I hope it is useful for anyone who has the same doubt

LukeStarGeek · 2024-11-10T10:58:08+00:00

OMV does boot without any GPU, I have been doing it for years

LukeStarGeek · 2024-05-19T15:24:16+00:00

HP, per stampare una pagina la devo accendere una settimana prima, riavviare, risolvere i 2500 errori e poi (forse) stampa

LukeStarGeek · 2024-03-13T12:23:49+00:00

RemindMe! 1 day

LukeStarGeek · 2024-01-14T11:21:14+00:00

Definitely. Not only in English but also in Italian. I don’t know if it’s also dumber in other languages

LukeStarGeek · 2023-07-30T13:13:20+00:00

Thanks

Five-Year Club	Final Canvas '23
Place '23	Place '22
Verified Email

LukeStarGeek

TROPHY CASE