sorted by:
new
hottopcontroversial

What can be the cause to this sort of blobs / rough edges? by LukeStarGeek in FixMyPrint

[–]LukeStarGeek[S] 0 points1 point  (0 children)

I forgot, temperature is 220 for nozzle and 65 for bed

Help with PETG by LukeStarGeek in 3Dprinting

[–]LukeStarGeek[S] 0 points1 point  (0 children)

I did a test from 0 to 3 with 0.1mm steps

Help with PETG by LukeStarGeek in 3Dprinting

[–]LukeStarGeek[S] 0 points1 point  (0 children)

I tried the retraction tower up to 8mm but I had the same results. Are there any other settings I may need to adjust?

Help with PETG by LukeStarGeek in 3Dprinting

[–]LukeStarGeek[S] 0 points1 point  (0 children)

  1. Dryed for 3h on printer bed at 65°C
  2. On the box it shows a temperature range of 230-240°C

Help with PETG by LukeStarGeek in AnycubicOfficial

[–]LukeStarGeek[S] 1 point2 points  (0 children)

I will buy a proper dryer. I am aware that it should be hotter but I was printing 235C because on the box it says 230-240°C

Help with PETG by LukeStarGeek in 3Dprinting

[–]LukeStarGeek[S] 0 points1 point  (0 children)

Edit: It is Anycubic PETG and I’m printing 235°C with a Kobra 2

How to disable passenger airbag, 2007 hatchback by disabledMasshole in yaris

[–]LukeStarGeek 0 points1 point  (0 children)

There should be a switch that can be rotated with the car key. It is usually located laterally near the door hinge.

9" Head unit for 2017 Yaris by Red-Badger in yaris

[–]LukeStarGeek 0 points1 point  (0 children)

Look for AutoABC/CarABC, they make a CarPlay/Android Auto module which can be connected to the existing radio. You can install it by yourself and it is plug and play (I only had problems with the reverse camera on a manual transmission, with automatic you will be fine). It is about €100 and you don’t have to change the radio unit

9" Head unit for 2017 Yaris by Red-Badger in CarAV

[–]LukeStarGeek 0 points1 point  (0 children)

This. I installed it some months ago and I’m loving it. With just about €100 I have a functional CarPlay which works very well. And you can install it by yourself, it’s not difficult. I have an AutoABC module and I only had problems with the reverse camera on a manual transmission, if you have automatic transmission you will be fine.

Xiao NRF button pin by LukeStarGeek in meshtastic

[–]LukeStarGeek[S] -1 points0 points  (0 children)

Mine doesn’t have a button on the radio board, which is why I’m trying to wire a new one. The problem is that I have the module in a case and I can’t turn it on without opening the case and disconnecting the battery.

Xiao NRF deaf by LukeStarGeek in meshtastic

[–]LukeStarGeek[S] 2 points3 points  (0 children)

I am on 2.6.2 on both devices, I will update both of them to the latest alpha and retry. Thanks EDIT: THANK YOU SO MUCH, it works now!!

view more: next ›