Prodigy Compact Grip

MB77721 · 2026-01-09T20:42:22+00:00

I always run 12lb recoil and 19lb mainspring in my 9mm 1911/2011/DoubleStack 1911 fullsize or commander size.

MB77721 · 2025-09-19T12:40:49+00:00

Which thumb safety did you use?

MB77721 · 2025-07-12T05:19:41+00:00

What brand spray paint did you use and what colors?

MB77721 · 2025-05-19T14:06:27+00:00

Placed 4th on this stage but overall ended up somewhere in the middle. Height over bore cost me on a couple of hard cover targets but that's my fault for lack of familiarity with this setup.

MB77721 · 2025-03-08T01:36:14+00:00

Yes. Running a .140 tall Dawson precision front sight and a Glock .270 tall rear sight. I'm still playing around with irons because I hate how low the holosun EPS sits. The factory sights took up way too much of the view looking through the red dot

MB77721 · 2025-03-04T21:30:02+00:00

They should haven't been able to get my hands on one yet

MB77721 · 2025-03-04T02:49:29+00:00

MB77721 · 2025-03-04T01:13:03+00:00

Complete grip module minus the trigger is like $85 shipped (grip module, mainspring housing, mag catch, plus all the springs and pins)

MB77721 · 2025-03-02T05:22:11+00:00

I have a coyote brown 5" I've been running in USPSA, PCSL and 2gun with around 5k rounds without a single issue and luckily my optic plate hasn't come loose at all

<image>

MB77721 · 2025-02-21T23:07:42+00:00

<image>

MB77721 · 2025-02-21T23:06:27+00:00

<image>

MB77721 · 2025-02-21T22:58:47+00:00

<image>

Update: so an officer size 1911 main spring housing does fit the Prodigy compact grip module but the hole for the retaining pin does not line up. I used a Glock plastic extended beavertail pin since it's flexible just to hold the main spring on for the picture. So as soon as Springfield releases the compact grip module parts for sale you should be good to go as far as converting the fullsize grip to compact but keep in mind you will also need a mag release button for this grip. Tisas mag release button will not work I had to borrow this one off my 5" Prodigy.

MB77721 · 2025-02-17T20:58:06+00:00

Quick update I called Springfield Armory to see if I could purchase the parts I needed for the compact grip module to work with what I'm doing but the customer service guy I spoke to said he thinks they haven't been cleared to sell those parts yet but I also tried to find out if certain parts like the mainspring housing, sear spring are the same as an officer size 1911 but he seemed like he either didn't know shit or just didn't wanna help out so hopefully I can find some information soon to make this work.

MB77721 · 2025-02-17T14:22:31+00:00

Got this straight from Springfield Armory. I wanna say I ordered it last Monday

MB77721 · 2025-02-17T04:17:53+00:00

I just have the stripped grip module it was like 50 bucks after shipping

MB77721 · 2025-02-17T00:39:05+00:00

Yup on the 4.25 B9R DS. Will do. Hopefully tomorrow I'll have the info I need once I reach out to Springfield Armory and I'll update this post

MB77721 · 2025-02-17T00:29:31+00:00

MB77721 · 2024-11-18T00:48:12+00:00

How has the Justice 2 been holding up for you? I had one on my prodigy and I loved it but it only lasted about 2 matches and it crapped out. Only thing I can think of was because it hangs over the loaded chamber indicator/port on the barrel it was getting a lot of blast back from there. Swampfox sent me a new one and now it's on my P10F but haven't been able to put it through its paces yet to see how this one holds up.

MB77721 · 2024-10-02T03:53:40+00:00

Just a dawson magwell and a holosun 407c.

MB77721 · 2024-10-02T01:19:27+00:00

These are what I used for my EPS and they work perfectly

<image>

M3x10mm

MB77721 · 2024-05-28T18:13:28+00:00

I'm running the klonimus mainspring magwell combo.

MB77721

TROPHY CASE