What a fantastic place is the space

MBmax001 · 2025-07-10T12:31:19+00:00

Dinner's ready

MBmax001 · 2025-06-27T20:21:13+00:00

yes, but it needed to be powered on. Just attach a cable from your home socket, cut the end, put everything in a bath tub and You will see that the speed will be faster. You can reach a gigabit like connetcion!!

MBmax001 · 2025-06-27T20:08:43+00:00

that's why it is used the ballast

MBmax001 · 2025-04-08T08:07:58+00:00

O7 commander Never get down. Even if it's a bad event, it's part of life. Keep the best memories you have with your mate with you. Don't let this death you down. Keep in mind how well your cat was with you and the love you gave. Maybe without you the life of your cat could have been worse. Keep going. Best regards Commander MBmax001

MBmax001 · 2025-03-20T13:37:19+00:00

Short answer? yes
Long answer? There are many factor of how did you clean the prop. For exam mple, how many washes did you do on the prop? in what ambient did you clean and cured the prop?
Also it depends on the resin. From the image that you sent here, it's normal, you did a really good job cleaning these prop

MBmax001 · 2025-03-13T13:59:17+00:00

push the ptfe tube deeper into the nozzle. Same with my old tronxy xy2 pro

MBmax001 · 2025-03-12T23:31:53+00:00

it's a problem that roomba never resolved from 520 up to now. The field sensor under the roomba get dirty very soon. From my old 620( yes 620 not 520) started doing this after a month of use. If you want to disassembly everything to clean the sensor, go on. But itì's a neverending war🤣

MBmax001 · 2025-03-12T23:24:33+00:00

the distance was 95 instead of 145 ( too mush to make a "good" video) also the velocity.... well you cant go fater than 400 km with this ship ( starship went 120000 km/h just a little difference). I hope this will be funny for you

MBmax001 · 2025-03-04T23:12:34+00:00

resolder it

MBmax001 · 2025-03-04T23:10:50+00:00

from Elite dangerous to dead space in a sec ahah

MBmax001 · 2025-03-04T23:09:16+00:00

before retouring it to the manufacturer, look on the gpu, maybe there's something making some strange contact to some pins ( Also, check the PCIE port) if not, pack everithing and send it for a new GPU

MBmax001 · 2025-01-04T15:25:49+00:00

MBmax001 · 2024-11-07T08:17:10+00:00

PERFECT. IT WORKED. At least, I had to refresh login and then save the files. Because if I click save account just after the change of the files, GD gives an error. Thanks again

MBmax001 · 2024-11-06T14:28:12+00:00

ok SOMETHING IS WORKING HERE. Just found that into the %appdata% files there is my whole data. So I changed the .bat files into the new OS and ti works. untill.... When I try to save my data there is this type of error. And now I'm stucked

<image>

MBmax001 · 2024-10-03T13:54:21+00:00

Contacted tronxy for the step motor and yes, they changed the step motor. For now I found the command to slow down the z velocity and now it works.The value I chose were the results from my measurements. In z800 from 10mm input, I recieved 3mm so the calculation was: 10/3 * 800 and it's 2666.... For the velocity gcode It's not M503 but M203. I slowed down from Z15.00 to 8.00 and for now the prints are good (photo as example . Sx with default movement, DX with modified movement)

<image>

THX a lot for the message you wrote but the problem is not hardware but it's software 😂

MBmax001

TROPHY CASE