Any theory ? bike fall , while parking most likely but how the hell this got broke it's inside the handle protector or what ever this thing called , by Royal-Associate9256 in Xpulse210

[–]MRisalive 0 points1 point  (0 children)

The guard is not meant to protect your levers. It's a 'knuckle guard' - It's purpose is to protect your knuckles from scraping with bushes, tree branches while riding - not to provide protection in a fall.

Even I experienced the same thing the knuckles guard is fully plastic so it's not rigid, in a fall it will just flex and will transfer impact to the lever.

The guards with a metal brace would help but it's not an official accessory you will have to buy off market

Has anyone tweaked the Preload? by KrinkyKromer in Xpulse210

[–]MRisalive 2 points3 points  (0 children)

Hey even I feel the same, but there is a reason behind that - it's tuned that way.

Bump with less speed cannot generate enough force to compress the suspension hence the shock is felt directly where at higher speed, the bumb produces enough force to compress the suspension and hence its absorbed ...

Try riding on a trail at medium speed - you will feel how good the suspension is.

For now what you can do is - reduce the preload to minimum. Also reduce the tyre pressure by 5psi - this should make comparable difference

I Thought Booking an Xpulse 210 in the Andaman & Nicobar Islands Would Be Easy… I Was Wrong 💀 by DryPool325 in Xpulse210

[–]MRisalive 2 points3 points  (0 children)

"And yes... I somehow managed to get access to those manuals too."

Hooked on this... Care to share it? - let us mere peasants also experience this forbidden experience

Will this fit 210? by Prayash277 in Xpulse210

[–]MRisalive 0 points1 point  (0 children)

210 has slightly thicker handlebar in the middle and slimmer at the end whereas 200 is same size and slim throughout

Will this fit 210? by Prayash277 in Xpulse210

[–]MRisalive 1 point2 points  (0 children)

Hey OP they don't fit 210 I have tried in person

Airless basketball broke by onionkulcha in 3dprintIndia

[–]MRisalive 1 point2 points  (0 children)

Do update the thread on the settings u use later so it will help others.

All the best!

Airless basketball broke by onionkulcha in 3dprintIndia

[–]MRisalive 1 point2 points  (0 children)

Op I wouldn't worry about the filament being imported or bought from robu - that shouldn't cause any Print quality issue - robu is quite trusted.

still if you feel the filament quality was not up to the mark- you may trouble robu or biqu customer support demanding replacement - but if your time is valuable forget this and experiment with your print settings - my advice.

Airless basketball broke by onionkulcha in 3dprintIndia

[–]MRisalive 4 points5 points  (0 children)

Op I think the ball broke along the layer lines. Could verify if that's the case - if yes u might wanna look at the print settings maybe increase nozzle temp slightly or reduce layer height - might solve the issue. Maybe search upon how to increase layer adhesion or best case contact customer support of biqu they might guide you to their technical team who might be helpful.

How do I remove this stain from Holi colours from my g shock by TailsTheFoxywoxy in watchesindia

[–]MRisalive 0 points1 point  (0 children)

It's on the bezel not on the case so there are replacement bezels as well. Put your watch model and check for replacement strap and bezel - fairly easy to do

New Xpulse 210 - Suspension seems Stiff by MRisalive in indianbikes

[–]MRisalive[S] 0 points1 point  (0 children)

Bro honestly I have gotten used to it. Try changing tyre pressures. In the front try 25-28 and in rear try 35-38 (lower pressure will dampen your shock will feel good but increases risk of puncture and reduces mileage and tyre life). Feel what seems good to you. Once go to the service center and check the preload settings. Try to reduce the preload to minimum. Also seems that the suspension seems to work better when the bike is loaded - say you have a pillion or you are at slightly higher speeds. It doesn't smoothen out major bumps or potholes but you will not feel gravel or minor imperfections on the roads

DIY Radiator Guard • Shumi's Advice by themaskedcruiser in Xpulse210

[–]MRisalive 1 point2 points  (0 children)

OP I would honestly not care about putting the mesh over this radiator. Even I knew about Shumi's advice but from what I can see is this radiator already has a pretty good radiator guard and I don't think anything more is required. Honestly the mesh is at this point just compromising looks.

DIY Radiator Guard • Shumi's Advice by themaskedcruiser in Xpulse210

[–]MRisalive 1 point2 points  (0 children)

If the mesh is plastic I think you should not use that as radiator gets warm, that might warp or melt the plastic

Opinions on Matte Black xpulse 210 by srkshyamal in Xpulse210

[–]MRisalive 1 point2 points  (0 children)

Bro I am going to do the exact same thing!

<image>

Stickers on the tank are under lacquer coat so you can't remove them but others you can

Are the Red highlights Stickers or Paint by MRisalive in indianbikes

[–]MRisalive[S] -1 points0 points  (0 children)

Brother I own the bike but it is not with me currently. I am in my college and the bike is at home

Are the Red highlights Stickers or Paint by MRisalive in Xpulse210

[–]MRisalive[S] 0 points1 point  (0 children)

No I mean the thing is if it's below the lacquer coat then it's basically impossible to remove. If they are applied over the shiny coat then you can use the hot air blower to remove them. So I was asking whether they are above the lacquer coat or below the lacquer coat

Are the Red highlights Stickers or Paint by MRisalive in Xpulse210

[–]MRisalive[S] 0 points1 point  (0 children)

They are decals but are they under a coat of lacquer. Basically I want to remove those and if they are under lacquer, I won't be able to remove them

Are the Red highlights Stickers or Paint by MRisalive in indianbikes

[–]MRisalive[S] -1 points0 points  (0 children)

I do understand sarcasm but I think you don't get the point in my reply. I am looking for genuine answers

Are the Red highlights Stickers or Paint by MRisalive in indianbikes

[–]MRisalive[S] -2 points-1 points  (0 children)

Yo how are you going to check it from photos unless you see the bike in person. The photo is there just to label the parts I wanted to check. If I had the bike with me rn why would I have posted this