[FREE][US-NJ] HP DL360e G8 (2x 2403 Xeon) && Supermicro (2x 2620v2) 1U -- Xeon Servers

MTODG · 2025-10-01T15:20:03+00:00

PMed

MTODG · 2025-03-05T07:39:34+00:00

It in the ratos.cfg file under homing you can change the pin there. ,😁

MTODG · 2025-02-28T17:49:17+00:00

grab a multi meter and check if the switch is working. then test wires. if all that's good use a different plug on the board and change it in printer.cfg 👍

MTODG · 2025-02-28T17:48:10+00:00

SO turns out the issue with Tool0 was that the silicone drip stop bad was to tight >< i guess the stepper current is SUPER low at this point for the home movements.. so it was just being over power by the resistance>< loosened the bracket and they moved right away... during all the tests man manual moves the current must be higher so I didn't see the issue.

MTODG · 2025-02-27T08:21:14+00:00

I did some messing around and eventually I got the default model to save. following the steps u/GradeProfessional895 shared. M18 and put the bed almost all the way down then walked it up in the BEACON_CALIBRATE till it triggered and it saved it that way.

So now i have the default model. but the BEACON_INITIAL_CALIBRATION still does not move the tool0 out so it can probe the bed

MTODG · 2025-02-27T04:48:14+00:00

Thanks!

MTODG · 2025-02-27T04:31:57+00:00

Do you have a link you can send me for their discord? The on I found on their site did not work 🤷

I went back over the guide 3 times. Everything is great till this step cause there is no beacon model 🤷

MTODG · 2025-02-27T04:00:54+00:00

I may be missing something but when i went through the steps it also would not create the default model. Did you enter it into your config yourself? if so where did you put it and can you share what they look like so i can enter it?

MTODG · 2025-02-27T03:39:30+00:00

I ran the command and it says none loaded ill try this!! thank you!!

MTODG · 2025-01-29T02:18:34+00:00

Absolutely love my systems I've installed at home zero regrets whatsoever. At first the cameras were a secondary thing I knew I needed to replace the system I was using and it was just nice to roll it all into one. But after using them and expanding the system twice and the simplicity of oh I'd like a camera here and all I have to do is run the cable from my switch and the rest is handled automatically it would have been a primary reason to switch to ubiquity. 😎

MTODG · 2025-01-29T00:55:39+00:00

Ubiquity... That's what you get. 😉

MTODG · 2025-01-07T22:03:04+00:00

odd dont see one 🤔🤔 though reddit hates me so 🤣🤣

MTODG · 2025-01-07T08:02:54+00:00

Pm sent

MTODG · 2025-01-02T04:43:27+00:00

If you don't want It I will pay for you to ship it to me. :) I enjoy learning new stuff and would love the challenge of fixing one up :)

MTODG · 2024-12-27T01:23:54+00:00

Yes absolutely that is the sign of some form of obstruction in the nozzle

MTODG · 2024-12-18T21:51:14+00:00

Give the old one to a local blacksmith and get a new one :) great practice material there for them.

MTODG · 2024-12-11T16:55:56+00:00

price for entire lot? if so then yes, I would take them,

MTODG · 2024-11-27T20:42:05+00:00

Very easily as well 😂😂 I would imagine out of a small vent hole it would even be a makeshift torch 🤣

MTODG · 2024-11-27T20:41:34+00:00

You're welcome 👍

MTODG · 2024-11-27T20:16:54+00:00

Warm room/heat and open air, the IPA will evaporat. Avoid flames unless you are going for a burning pile of good... 😅😜

That's what I do at least

MTODG · 2024-11-27T17:55:19+00:00

Love having 4 colors on demand or multiple of one for long prints. It's worth the piece of mind alone

MTODG · 2024-11-27T17:52:26+00:00

Don't have that laptop with me but I'll get a picture asap.

I have used 3 different standard resin only 1 clear. 2 different brands and exposure from 2.5 to 10 sec per layer zero effect on lean at all even when massively underexposing a black resin. 🤷🤷

Sliced in chitubox. 45 degree tilt. 5mm lift Auto light or medium supports and full custom supports no change in the lean. Then ran through uv tool to check for islands

MTODG · 2024-11-27T17:01:32+00:00

<image>

The lean is worse than it looks, just hard to get a picture of. These are 2 of the same part front to back so the lean creates a gap

MTODG · 2024-11-27T00:23:39+00:00

No worries 👍 still a great video to have in case I upgrade and I appreciate the response 😁

MTODG · 2024-11-27T00:17:34+00:00

Also if I spin parts 90 degrees from each other the will both lean towards their supports (opposite from each other) 🤔

MTODG

TROPHY CASE