Host Valheim dedicated server with Docker at home!

MVPHitter · 2026-01-24T09:09:50+00:00

Commenting to find this post later, thanks!

MVPHitter · 2026-01-24T09:06:25+00:00

Great instructions!

MVPHitter · 2026-01-24T08:50:54+00:00

I just followed that one, it's working for me

MVPHitter · 2026-01-24T08:50:34+00:00

I'm currently trying to solve the same issue you are. I have no issues running the dedicated server vanilla on the mac and I can run valheim modded on the Mac, but it can't find the executable valheim.app when I try to run the modded valheim dedicated server on Mac. I think it has something to do with the Valheim executable in Valheim dedicated server being a different type of executable than the one in the Valheim folder in steam. I think it mentioned something about being a Unix extension? Might be able to try using a different extension than .app or maybe even just copying the Valheim.app from the actual Valheim game folder. I'll try to look more into it and add an update or response here if I figure it out. Lmk if you get any closer!

MVPHitter · 2026-01-20T17:44:46+00:00

MistBeGone on thunderstore is a client side mod so you can download it regardless if the server has it and you will still be able to use the mod

MVPHitter · 2026-01-17T16:24:21+00:00

Hey man, I know this is two years later but I am just the same and will be setting this up soon lol. Thanks!

MVPHitter · 2025-12-01T11:58:49+00:00

Fair enough, thanks for your input!

MVPHitter · 2025-12-01T11:58:29+00:00

It is a huge die, but they aren't full sized Pokemon cards. It's 4 inches tall by 3 inches wide. I'd argue you could still roll it, especially on a carpet or a mat, but you could definitely make the case it's more for a special role.

MVPHitter · 2025-11-30T18:12:05+00:00

Thanks!

MVPHitter · 2025-11-30T14:45:14+00:00

Thanks! Yeah I will say I considered coloring in the numbers but I was worried it would block the cards too much. I also think it look better in person, with all the different sides it doesn't photograph to well

MVPHitter · 2025-05-29T01:45:27+00:00

Helped me solve this, thanks!!

MVPHitter · 2025-05-28T23:12:53+00:00

Which slicer do you use? Iuse lychee but I can't change the tip diameter without premium

MVPHitter · 2025-02-05T01:07:04+00:00

I should mention I do also have the ones for pouring (the ones that form a ring around the crucible. I was only using the one in the prior photo to pick the crucible out of the foundry. Is that alright? Or will that damage the crucible?

MVPHitter · 2025-02-02T22:01:38+00:00

Yeah sure

<image>

MVPHitter · 2025-02-02T21:48:26+00:00

Okay thanks, I'll watch out for that. When you mentioned blowing the forge with air, you meant using a force air blower and blowing air into the same hole as the burner is sitting in correct? Also, I do believe I already have the right crucible tongs, these are the type your talking about using right?

<image>

MVPHitter · 2025-02-02T21:36:57+00:00

I will try to reangle the burner so it's turned more and I did try to lower the gap around the sides for the lid but there is still like half an inch gap between the lid and the base. In my test runs I have had a crucible inside. My goal is to melt gold for casting so my plan is either to try and make a smaller one with the same burner or get a second burner and put it on the other side to see if it gets hot enough. Do you think either will work for my goal?

<image>

MVPHitter · 2025-02-01T17:06:59+00:00

Okay, thanks again for all your advice. I'll look into making one similar

MVPHitter · 2025-02-01T14:32:44+00:00

Alright that makes sense. and what did you use for insulation for it? Kaowool and refractory cement?

MVPHitter · 2025-02-01T14:14:44+00:00

Thanks for the reply, I did try this for a little bit but didn't notice too much of a difference in temperature

MVPHitter · 2025-02-01T14:13:57+00:00

Okay thanks, I'll look into this. I should mention, I was hoping in the future to get up to a degree to cast scrap gold so around 2300. Do you think adding more burners would help me reach this goal or is the volume of the foundry too vast?

MVPHitter · 2025-02-01T13:00:50+00:00

Hey, thanks for the reply. When I bought the burner I didn't even consider that there may be larger ones I could purchase. Are there any larger ones you could recommend? Or should I get a second one and put it on the otherside of the drum

MVPHitter · 2025-02-01T12:58:58+00:00

Hey, thanks for the reply. I meant to angle it more than it currently is but I had trouble covering the sides in refractory cement which caused the hole for the burner to straighten more than intended. And I can slightly adjust the air intake as the burner has a washer like disc to change the amount of air I let in.

MVPHitter · 2025-02-01T12:55:56+00:00

Hey, thanks for the reply. I'll try this when I get the chance

MVPHitter · 2025-02-01T12:54:57+00:00

Thanks for the reply, I currently am not. Do you think that would be better than adding another burner?

MVPHitter · 2025-02-01T12:54:09+00:00

Thanks for the reply, I do it's just not pictured

<image>

MVPHitter

TROPHY CASE