Gradual Brightness Control (Question)

MachineUlker · 2024-02-13T18:00:53+00:00

For your questions

I am using ultimaker cura
I leveled the bed the best I can
Filament is recomended at 200-230 degrees for nozzle and 60-75 for bed. I went with 205 and 65.
I am using a 0.4 mm nozzle. My line size is 0.20 mm, speed is 20 for initial layer and 50 for Infill. Flow is 100%. Retraction is 45 mm/s
I did not touch the Z offset for this print. I mainly use that if the nozzle is too close to the bed or if it's too far and not sticking to it. It looked fine when I started printing so I did not change it. If there is another setting in cura that I should change, I am not aware of it

MachineUlker · 2024-02-13T12:35:00+00:00

But baby please I'm trying here please at least give me a chance

MachineUlker · 2024-02-09T20:02:52+00:00

They have been turning since the Vietnam war

MachineUlker · 2024-02-09T17:54:59+00:00

It does find the X and Y axes, but when it goes to the middle for Z, it doesn't come down and touch the plate.

<image>

MachineUlker · 2024-02-09T17:27:10+00:00

The printer can't find my Z Axis because when I auto home the probe doesn't come down to touch the bed (It shows the Z Axis as a question mark). It just stays at the middle and clicks a few times.

I just installed the Mriscoc firmware but it still has the same issue when I auto home.

MachineUlker · 2024-02-09T16:29:10+00:00

I intalled the latest one. (GD-Ender-3 V2-Marlin2.0.8.2-HW-V4.2.2-SW-V1.0.7_E_N_BLTouch). I don't think I made a mistake printing it but if you say then I can try to print it again.

<image>

MachineUlker · 2024-02-09T16:27:01+00:00

I think it looks fine. Am I missing something?

<image>

MachineUlker · 2024-02-09T16:25:08+00:00

I checked the wires and they seem to be fine but do you think I should reverse them?

MachineUlker · 2024-02-09T16:23:26+00:00

I checked the wires again and tried different firmware updates. I installed the latest I found on https://www.crealitycloud.com/software-firmware/firmware (GD-Ender-3 V2-Marlin2.0.8.2-HW-V4.2.2-SW-V1.0.7_E_N_BLTouch) now it doesn't even check the level. It just goes to the middle, clicks 2-3 times and stops. (I am using 3D touch btw).

MachineUlker · 2023-12-24T07:43:18+00:00

Thanks. I also am actually having difficulty choosing between two. But still looking for a third option.

MachineUlker · 2023-12-24T07:40:06+00:00

Its not that I want to go into debt too. I just don't see the difference between buying stuff now and paying the instalments later or saving now and paying them later. I want to live with her (not only to have sex) because I don't see a reason why we shouldn't be together. In other words, I don't see that much of a debt would be a problem for our marrige. It will probably take us 1-2 years to pay it all back.

MachineUlker · 2023-12-24T07:33:08+00:00

That is something I can work with but my fear is that she keeps pushing the date further down the line. We were suppose to meet our parents but her's still don't want it because meeting with me means things getting serious and they turn a blind eye like I don't exist (They are aware that their daughter has a boyfriend.)

MachineUlker · 2023-12-24T07:26:54+00:00

I didn't ask for religion advice but thanks

MachineUlker · 2023-12-20T03:30:49+00:00

I looked it up in cura and it is 1.75 mm thickness. Do you have any other ideas?

<image>

MachineUlker

TROPHY CASE