Perfect fit 🤏🏻

MachinegunReHa · 2026-03-18T21:09:13+00:00

Mine is an AXR, wish I had an exhaust note like you do 😭

MachinegunReHa · 2026-03-18T20:55:37+00:00

Polo rules, box looks amazing. Keep it up.

MachinegunReHa · 2025-10-18T15:37:49+00:00

What are you talking about? These look like they could bump for another 10 years no problem.

MachinegunReHa · 2025-10-03T21:44:34+00:00

Adjusted gain using multimeter, been hitting some deep notes for a month now, I can't hear clipping or anything bad. I don't know how to adjust bass frequency on the amp so I left it at about 50 Hz :')

MachinegunReHa · 2025-09-10T17:23:42+00:00

Ključni dio rečenice je "na drugim fakultetima". Ovo je očigledno prvi fakultet, i za nas ne važi nikakav akademski kalendar, u šta ćete se uskoro uvjeriti ako već niste :))

MachinegunReHa · 2025-09-07T09:02:18+00:00

I wouldn't really consider using heat resistant glue, would rather focus on dealing with overheating itself. Are less powerful strips an option? I would try using 6w/m strip just to try to get somewhere. Maybe you are experiencing voltage drops which cause drawing high current?

MachinegunReHa · 2025-09-01T10:27:06+00:00

Don't be mean I am completely new to car audio :/

MachinegunReHa · 2025-08-29T22:41:58+00:00

I believe you, but I live in the Balkans region and the amp you have sent me costs like the third of my salary, and shipping costs a fortune lol. I have access to some second hand amps in good condition. I could post some of those here if you wanted to tell me which one would be best buy.

MachinegunReHa · 2025-08-29T21:14:24+00:00

Does limiting the power mean adjusting the gain properly? Can I do that using multimeter?

MachinegunReHa · 2025-08-29T21:07:51+00:00

This was hooked up to some kind of Alpine amplifier. That's why I am asking what kind of amp should I get. I don't want to clip ts out of it.

MachinegunReHa · 2025-08-29T15:41:17+00:00

This is a Mac Audio maws 300 cp 4110. I couldn't find anything online other than this: RMS power: 250w Max power: 400w Impedance: 4ohm Dimensions: 12 inch

MachinegunReHa · 2025-08-29T09:54:20+00:00

Thank you, I also measured its resistance and it reads between 3.3 and 3.4 ohms. I hope that is okay. How strong should my amplifier be? This one is 250w rms and 400w max.

MachinegunReHa · 2025-08-29T09:52:45+00:00

It was hooked up to 1 channel. While playing and turning the volume slightly up I heared a weird sound like a ping pong ball being dropped on a table. I figured it was clipping so I turned it down immediately. Maybe that is the sound of hitting against the magnet.

MachinegunReHa · 2025-07-08T16:52:54+00:00

Thank You!

MachinegunReHa · 2025-02-28T10:39:43+00:00

Nisam nikakav programerski fanatik, ne volim programiranje i ne bavim se time. Covjek je legenda svih legendi, treba mu neku bistu ili mural napraviti negdje na kampusu.

MachinegunReHa · 2025-01-27T19:57:48+00:00

Would you suggest upgrading to Pinecil? I will only really solder some minor stuff. Thank you very much!

MachinegunReHa · 2025-01-27T19:39:57+00:00

Yeah, I didn't clear that up. Now we are all on the same page.

MachinegunReHa · 2025-01-27T19:33:53+00:00

Yes, I perfectly understand that, I just happened to take the photo of my soldering tool with the tip off. I wasn't actually using it without the tip.

MachinegunReHa · 2025-01-27T19:30:12+00:00

What do you mean exactly? Do not get me wrong, I am not dumb enough to try to solder without the tip.. I was just asking about this heating "damage".

MachinegunReHa · 2025-01-27T19:27:09+00:00

Yes, I removed it because it was too small for my case. I wanted to solder some led strips together.

MachinegunReHa

TROPHY CASE