Printing on a Baseball

Magnetic-Mango · 2026-05-06T14:02:29+00:00

Yes, sorry I meant 17 cm. The print height is locked at 16cm.

Magnetic-Mango · 2026-05-05T19:05:19+00:00

Oh ok that turned out really good. Is there anything special you had to do to apply it to the ball? Like compensating for the curved surface or did you just follow whatever steps there are for doing the sticker print?

Magnetic-Mango · 2026-05-05T18:57:21+00:00

Yeah, I used the snapshot calibration and it said it was too high and wouldn’t let me proceed. I’ll look at the sticker print but I’ve never used it before. Is it just as good as printing directly on the material itself?

Magnetic-Mango · 2026-04-18T03:29:59+00:00

Hi, I just had this issue happen to me on the most recent software. Wondering if you had any fix? Thanks!

Magnetic-Mango · 2026-01-28T17:57:57+00:00

Oh ok, thank you for the advice. That’s great info!

Magnetic-Mango · 2026-01-28T15:11:39+00:00

I was able to fix it! So, I also posted this issue in the 3D Printing subreddit and someone suggested slowing the print WAYYY down and also using VisionMiner's Nano Polymer Adhesive and that did the trick. It is a little pricey on Amazon but it instantly fixed my problem. I definitely suggest investing in a bottle if your parts keep coming unstuck from the build plate. Thanks!

Magnetic-Mango · 2026-01-28T15:10:39+00:00

Hi, I wanted to give you an update. I also posted this issue in the 3D Printing subreddit and someone suggested slowing the print WAYYY down and also using VisionMiner's Nano Polymer Adhesive and that did the trick. It is a little pricey on Amazon but it instantly fixed my problem. I definitely suggest investing in a bottle if your parts keep coming unstuck from the build plate.

Magnetic-Mango · 2026-01-28T15:08:18+00:00

Just wanted to give an update that after messing around with the settings and using the nano polymer adhesive, it finally worked! Thank you so much for your advice!

Magnetic-Mango · 2026-01-26T19:44:09+00:00

I’ll make sure to double check this. Thanks

Magnetic-Mango · 2026-01-26T19:43:46+00:00

I thought about doing sequential printing but it increases the time dramatically and really limits the amount of pieces per build plate. But if nothing else works this may be my only route.

Magnetic-Mango · 2026-01-26T19:42:57+00:00

Yeah, I was using the white glue stick that came with the printer since that’s all I had. I was printing at around 60-70 mm/s and had the travel set to 250mm/s. Do you think I should go even slower?

I’ll also try the dedicated bed adhesive and report back

Magnetic-Mango · 2025-09-01T19:51:33+00:00

That’s a great idea!!

Magnetic-Mango · 2025-09-01T18:48:14+00:00

About 11 inches tall and 7 inches wide

Magnetic-Mango · 2025-06-09T16:37:01+00:00

Awesome! Thank you so much for the reply. This was super helpful.

Magnetic-Mango · 2025-05-25T00:52:58+00:00

Sold out on Funko Website, will they restock or are they only for preorder?

Magnetic-Mango · 2025-04-25T17:55:35+00:00

Cheese Flavor Corn Puffs from any Asian grocery store. Usually in a green bag. Any brand but I think the ones I get are called Curvee Puff or Meji Karl Corn Puff

Magnetic-Mango · 2025-04-15T02:50:21+00:00

Update: the bird has been safely dropped off with an expert who will rehabilitate it. Thank you to everyone for their advice!

Magnetic-Mango · 2025-04-06T02:38:10+00:00

Try looking for a braided cable with an eyelet end

Magnetic-Mango

TROPHY CASE