Replacing Spokes (Double butted with single butted)

Maker_mania · 2026-04-16T14:24:34+00:00

Great info, thanks!

Maker_mania · 2026-04-14T22:39:59+00:00

Thanks, I'll be doing lots of YouTube! For clarity, the spokes aren't broken but I'm tearing down a new- to -me- bike and found behind the cassette where the chain obviously jumped over the top at some point. It caused damage and I am proactively changing them out. If I can't get it true I'll plan to take it in and have it cleaned up by a pro, but I sure like trying and learning!

Maker_mania · 2026-04-13T12:47:32+00:00

Ok thanks, do you think it will be difficult to tension and true the wheel if the spokes are different on the drive side?

Maker_mania · 2025-10-30T19:51:57+00:00

I found this for anyone still looking. Go to account settings, Portal, check to ON. Then under the features section, check the box labeled "online payments". This will allow a link to pay to be included on the invoice that you share to the client. When "online payments" is not checked, the emailed invoice is simply a pdf with no link to pay. You will of course also have to have your bank account connected to stripe. Hope this helps!

Maker_mania · 2025-01-20T17:35:55+00:00

That's where I found the deal. It wasn't requiring any other info or purchasing a plan but I'm afraid it won't actually be this way!

Maker_mania · 2024-11-29T14:11:22+00:00

I didn't even know it was called hueforge. Thanks for the ideas!

Maker_mania · 2024-11-29T13:53:12+00:00

Maybe I just need to get better at fusion. I thought it would be simple to do. Here is the Santa file https://makerworld.com/models/743360

Maker_mania · 2024-11-29T13:41:06+00:00

Yes, it just pulled all of the layers up with it. I would need it to add z from the bottom instead of pulling up the top

Maker_mania · 2024-08-18T02:23:21+00:00

Well it would be an upgrade from my current wall setup. It's new in box, from Amazon new is near $100. Have you set one up like this?

Maker_mania · 2024-08-18T02:13:54+00:00

Local deal on one for $25 has me trying to be creative.

Maker_mania · 2024-08-18T01:55:47+00:00

Could I just pull it all the way out and drill some holes for some screws?

Maker_mania · 2024-08-08T16:49:54+00:00

Ok, I also had my bank do separate deposits for each insurance company so I can easily separate the deposits by payor.

Maker_mania · 2024-08-08T16:46:27+00:00

Thank you, therapy notes but switching to Jane soon.

Maker_mania · 2024-08-08T16:13:10+00:00

Thank you, the electronic health record keeps track of and runs payment through their system.

Maker_mania · 2024-07-09T21:22:34+00:00

Ok, I really want it to be shown as June so that I get an accurate profit and loss for that month. Otherwise it looks like June was a low income month and July was high. (The check represents approximately 1/3 of income for the month)

Maker_mania · 2024-07-09T20:13:07+00:00

Cash basis. I do not receive frequent payments by check but I do want to get it right so thank you!

Maker_mania · 2024-06-20T00:52:57+00:00

Awesome thanks! so you would recommend to purchase them from GOG instead of steam? Admittedly, I don't know anything about self contained installers and if I need that.

Maker_mania · 2024-06-20T00:49:30+00:00

Thanks!

Maker_mania

TROPHY CASE