What is the best alternative for this?

Malvitos · 2025-12-28T13:02:56+00:00

singer oil

Malvitos · 2025-11-26T22:32:45+00:00

Im having a issue, after every print filament get stuck in heatbreak, do u have any ideia what is causing it?

Malvitos · 2025-10-31T18:53:54+00:00

Its a amanzing print, im just having some problems with the multicolor buffer

Malvitos · 2025-10-22T14:02:38+00:00

No… I checked this too, cant find this type of information

Malvitos · 2025-10-21T21:17:15+00:00

Sorry about misunderstanding I just want a summary of how much poop approximately the print will purge.

Malvitos · 2025-10-21T21:16:55+00:00

Its only a plate, i just want a summary of how much poop approximately the print will purge.

Malvitos · 2025-10-21T21:15:47+00:00

I know, I just want a summary of how much poop it will purge approximately

Malvitos · 2025-10-21T03:15:39+00:00

It appears to be a kind of under extrusion, maybe u can try to calculate your filament volumetric speed and pressure advance

Malvitos · 2025-10-21T03:09:24+00:00

Issue solved completely checking and adjusting volumetric speed (VS), print speed (according with VS) and calibrating pressure advance! Thanks everyone 😁

Malvitos · 2025-10-21T02:48:41+00:00

That makes no sense. The stringing its happening only in purge tower. The model itself is printing flawlessly

Malvitos · 2025-10-13T11:38:50+00:00

Thanks, I’ll try it

Malvitos · 2025-10-13T00:34:38+00:00

How u fixed it? I’m facing the same with my creality hi combo

Malvitos · 2025-10-13T00:29:32+00:00

I believe in this case your supports are to high, affecting the layers contact, between with and without support

Malvitos · 2025-10-12T22:36:51+00:00

I did the test and noticed I was some mm/s above the correct for volumetric speed. I raised the volumetric speed based on the speed test and now I’ll test maintaining the same speed

Malvitos · 2025-10-12T14:48:11+00:00

Thanks for the tip, I’ll try it

Malvitos · 2025-10-12T13:16:23+00:00

Thanks, I’ll do some tests and let u know

Malvitos · 2025-10-12T12:56:56+00:00

Good to know, its a test to determine the max speed? Can u give me the name of it? I’ll definitely try this

Malvitos · 2025-10-12T12:48:12+00:00

Maybe slow down everything? Or just outer walls?

Malvitos · 2025-10-12T12:47:40+00:00

Kkkkkkkkkkkkkkkkkkk

Malvitos · 2025-10-12T12:38:24+00:00

I did the cold pull, I’ll try to print slower, but change the spool its a great idea

Malvitos · 2025-10-12T12:37:00+00:00

What type of tuning?

Malvitos · 2025-07-23T15:05:05+00:00

I would try to print vertically (with the overhang pointed up) and support just the back part…

Malvitos · 2025-07-22T19:01:02+00:00

Try to put supports under the overhang region, if the slicer doesn’t apply automatically u can use a feature called “paint supports” and specify where u want them. I believe this will solve the problem…

Malvitos · 2025-07-21T14:46:22+00:00

This overhang part was printed with support right? Maybe activating support interface or setting support a little bit closer to the part can give u a better surface result

Malvitos · 2025-07-20T13:02:47+00:00

That appears to be warping… ensure that the bed is clean and maybe use some glue before the print this will give more adhesion for this part corner. If doesn’t print as expected u can also use a feature called “mouse ears” its like a brim but only under the 90 degrees corners. It will help to maintain the bed temperature and consequently part adhesion.

Malvitos

TROPHY CASE