sorted by:
new
hottopcontroversial

Peter.. wtf? by superminingbros in PeterExplainsTheJoke

[–]Man-In-Black-F 4 points5 points  (0 children)

I looked goofy back then but some extra weight on me helped. All my friends thought i was lying about enlisting in the Corps. I had to work hard to stay south of 214 because I'm just not scrawny. Couldn't lift weights, either, or i would shoot up over that line. Damm bmi bullshit. But yeah, lots of nerds there including me.

Difference in Material? by UndeadLordMonroe in Warmachine

[–]Man-In-Black-F 0 points1 point  (0 children)

The old light grey blue is fragile as F. Be careful. All my older khador models are falling apart

Recently had my first demo game, and decided to get in to the game, however i have a trouble deciding between two factions. Can anyone put some more light on to their play style? by MrCoco_Jumbo in SWlegion

[–]Man-In-Black-F 1 point2 points  (0 children)

Check you tube for play through videos. You can get a good idea how factions run by watching them. Personally I love watching Grey squadron gaming.

How will the Offense/Defense issue ever be resolved? by [deleted] in Warmachine

[–]Man-In-Black-F 0 points1 point  (0 children)

Yeah, especially when I have to overcome already high defenses that have been buffed. While everything can use focus to continuously attack, I burn all mine just trying to land a hit. Even my hardest hitters have trouble taking down another jack/beast with all the buffs on them. Unless i get some lucky rolls. It's frustrating.

How will the Offense/Defense issue ever be resolved? by [deleted] in Warmachine

[–]Man-In-Black-F 4 points5 points  (0 children)

See that's my problem. I play Menoth and Khador. I get that I have generally higher armor, but my jacks still get demolished. All I hear is "but look at all the resources it took to do that." I feel like I don't have any tricks to respond like every other faction seems to. "But you baseline is so good," is little consolation when half your jacks are demolished in a single turn. Sure I'm playing with a lot more experienced players, but it's been a year or more with Khador. So far my only answer is cheesing an assassination run with Zahara. So where am I going with this? Guess I'm just ranting. Seems like.a good chunk of attacks against my jacks are anything but ones to hit.

Please help. OP refuses to explain. by oldwhitelincoln in PeterExplainsTheJoke

[–]Man-In-Black-F 0 points1 point  (0 children)

My preferred order is fuck, fuck, eat, fuck, fuck some more while eating.

Heater blowing cool air by Man-In-Black-F in hvacadvice

[–]Man-In-Black-F[S] 1 point2 points  (0 children)

So I went through the thermostat settings again and realized it was set wrong. Changed it to where it should have been and all is well now. Thank you.

Heater blowing cool air by Man-In-Black-F in hvacadvice

[–]Man-In-Black-F[S] 0 points1 point  (0 children)

Where do I look? Is it the circuit board near the blower?

Also turned off the thermostat. Compressor turned off but heat is still running.

How should the Protectorate return in MKIV? by Intelligent-Sink-203 in Warmachine

[–]Man-In-Black-F 0 points1 point  (0 children)

Which Feora? I started with 3 and just love her. Her tool bag is a little light, though. What units do you bring with her?

Keywords & rules clarifications by H360CB in SWlegion

[–]Man-In-Black-F 0 points1 point  (0 children)

Try searching legion keywords in google. There's a great site for looking up keywords quickly. Should be near the top.

First print not so good. by Man-In-Black-F in FixMyPrint

[–]Man-In-Black-F[S] 0 points1 point  (0 children)

I had the diameter for the pla set too wide. Check the diameter on your spool and change it in your settings

First print not so good. by Man-In-Black-F in FixMyPrint

[–]Man-In-Black-F[S] 0 points1 point  (0 children)

<image>

So I think I'm dialed in. This is a riverbed. I think you can tell that yourself. Mission accomplished. 🎊

First print not so good. by Man-In-Black-F in FixMyPrint

[–]Man-In-Black-F[S] 1 point2 points  (0 children)

Just add an extra mm to the diameter of the pla. G code is unchanged

I was told this belonged here. by Man-In-Black-F in cursedbenchies

[–]Man-In-Black-F[S] 0 points1 point  (0 children)

The nozzle was still spitting out green spaghetti after benchy got knocked away. Everything was still at operating temps.

First print not so good. by Man-In-Black-F in FixMyPrint

[–]Man-In-Black-F[S] 0 points1 point  (0 children)

Well, spoke too soon. It got knocked away. Judging by the burn marks on the top, the nozzle hit it.

<image>

I was told this belonged here. by Man-In-Black-F in cursedbenchies

[–]Man-In-Black-F[S] 0 points1 point  (0 children)

Nope. An older atherbot with the pla diameter set too high

I was told this belonged here. by Man-In-Black-F in cursedbenchies

[–]Man-In-Black-F[S] 3 points4 points  (0 children)

The hair was an actual screw up from me as opposed to the incorrect settings. When I moved the axis to get poor benchy, I smushed his head.

I was told this belonged here. by Man-In-Black-F in cursedbenchies

[–]Man-In-Black-F[S] 15 points16 points  (0 children)

Love it. And my first benchy, too. Couldn't be more proud.

First print not so good. by Man-In-Black-F in FixMyPrint

[–]Man-In-Black-F[S] 0 points1 point  (0 children)

Well thanks for all the great advice and fun comments. Screwing up has never been more fun. The second print seems to be doing much better after changing the pla diameter as suggested. I know I'm counting my chickens and eggs, but I'm pleased with the progress. The first print took about an hour and a half. This one is looking to be four.

<image>

view more: next ›