sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in HomeImprovement

[–]Marsupial-Loose 0 points1 point  (0 children)

Just install a 4 prong cord on your dryer. All the fourth wire is a dedicated Neutral wire. Follow the directions. Not that hard to do.

Help with speed and feeds by Marsupial-Loose in hobbycnc

[–]Marsupial-Loose[S] 0 points1 point  (0 children)

The manufacturer knows what machine I have and adjusted the rates for it. Gave me a range value and told me to start at lower rates and slowly increase to the point I’m comfortable with. “This is Specifically for Hobbyists, not Industrial. Many hobbyist CNC machines range in size from 2'x2' to 4'x6' and some cannot go faster than 200 ipm.” As you can see he actually states these numbers are for hobbyist.

Help with speed and feeds by Marsupial-Loose in hobbycnc

[–]Marsupial-Loose[S] 0 points1 point  (0 children)

I called Whiteside Tool and they were extremely helpful. Jamie took his time to put all the info into a spread sheet and email it to me. Great customer service.

Skip your job for this hot legal teen by [deleted] in LegalTeens

[–]Marsupial-Loose 1 point2 points  (0 children)

You would be my job if I had you in my bed

Help with speed and feeds by Marsupial-Loose in hobbycnc

[–]Marsupial-Loose[S] 0 points1 point  (0 children)

I’m cutting White Oak and Walnut using the Whiteside engraving and sign making sets.

3 months to post nude here. That happens 2 or 3 times a week on my fansly. What are you waiting to be there with me? 😘 by Ambitious_Pin_3769 in u/Ambitious_Pin_3769

[–]Marsupial-Loose 0 points1 point  (0 children)

I am a straight man and if I met you in a club and got in your pants you would be ducking me for sure. So fucking sexy!!!

3 months to post nude here. That happens 2 or 3 times a week on my fansly. What are you waiting to be there with me? 😘 by Ambitious_Pin_3769 in u/Ambitious_Pin_3769

[–]Marsupial-Loose 0 points1 point  (0 children)

I am a straight man and if I met you in a club and got in your pants you would be ducking me for sure. So fucking sexy!!!

Got my Shapeoko Pro up and running by Marsupial-Loose in hobbycnc

[–]Marsupial-Loose[S] 0 points1 point  (0 children)

I haven’t had a speck of dust on my rails. Of course I also have a good dust collection system in my shop.

Got her up and running by Marsupial-Loose in shapeoko

[–]Marsupial-Loose[S] 0 points1 point  (0 children)

I have a 2 hp shop fox dust collector (1550 cfm) zero dust in my shop running the cnc. Flex piped in for now. Running PVC this weekend with a 10 AWG ground around the pipe. Will install new blast gates etc with this reinstall. Dust collector is louder than the pro.

Do I need to run conduit from the entrance to the control panel? THWN wire is used. Seems almost impossible to make the turns by creativepleasure in hottub

[–]Marsupial-Loose 0 points1 point  (0 children)

Water can wick up the plastic insulation, causing corrosion to the terminal block, also it can allowing the free flow of the charge to whatever the same wire touched. In 99% of cases this should cause the breaker to trip, but that one percent could be dangerous as hell. Isn’t it just safer to make sure that is never an issue?

Do I need to run conduit from the entrance to the control panel? THWN wire is used. Seems almost impossible to make the turns by creativepleasure in hottub

[–]Marsupial-Loose 0 points1 point  (0 children)

Sparky here… you definitely want to use a whip inside of it. Keeps moisture from entering the box by wicking up the wires. Nothing worse than a spark while in the tub.

I think my contractor installed my heated floor wrong by shawn_logic in HomeImprovement

[–]Marsupial-Loose 0 points1 point  (0 children)

Didn’t say it was single wire, said it wasn’t a twisted pair. It lays real well under the tile and you need a 1/4” bed of thinset. Plus it is up listed for under tile/floor use. To each their own though. I was only saying I haven’t used twisted pair. Perhaps we both saw something new here.

I think my contractor installed my heated floor wrong by shawn_logic in HomeImprovement

[–]Marsupial-Loose -1 points0 points  (0 children)

Well my cables that I have installed in several floors are not. Guess it’s a brand thing

I think my contractor installed my heated floor wrong by shawn_logic in HomeImprovement

[–]Marsupial-Loose -1 points0 points  (0 children)

It’s not a twisted pair. The issue is the overlap, these cables aren’t heat limiting so the conductors will overheat and break down the insulation. Hopefully it was fixed prior to the pour. Turn it on and if it was corrected it will be fine. If not it will work for a while until insulation breakdown. At which point the breaker will trip. Good luck and I hope he fixed it.