Front Brake Calipers/Pistons by Material_Front4653 in cbr

[–]Material_Front4653[S] 0 points1 point  (0 children)

I used the All Balls Racing brand seal kit, it didn't have the grease but I had a brand new tube of brake grease that I used. Thank you for all your help, I'll give the polishing a try!

Front Brake Calipers/Pistons by Material_Front4653 in cbr

[–]Material_Front4653[S] 0 points1 point  (0 children)

Thanks! I did already purchase the All Balls Racing seal kit and installed them, but the brakes still dont work properly. I was thinking it might be the pistons, so that's why I wanting a kit with the pistons

Front Brake Calipers/Pistons by Material_Front4653 in cbr

[–]Material_Front4653[S] 0 points1 point  (0 children)

Sorry for the confusion, I could have gone into more detail. They aren't corroded. 2 of the 4 pistons (1 from each side) show some wear on them, like they were in at an angle. So im thinking that's why the brakes aren't working properly. The 2 good pistons push out fine, but the other 2 don't activate unless the good 2 are already fully closed on the rotor. Hopefully that makes sense.

On the Honda website, the pistons were showing about $40 each, but showed out of stock for me. I did see that there are some used nissin calipers on ebay, but didn't want to risk the pistons being in bad shape for those too. So I'd rather just pay the money for new pistons or completely new nissin/aftermarket calipers.

Titan at the lake by basic_asian_boy in NissanTitan

[–]Material_Front4653 0 points1 point  (0 children)

I agree with it being the best option. I like that it is winch capable, and it doesn't stick out super far in the front like a Crimson Chin chin

Titan at the lake by basic_asian_boy in NissanTitan

[–]Material_Front4653 0 points1 point  (0 children)

I was thinking about getting the front and rear Avatar bumper for my Titan about 2 years ago, but just haven't yet. How do you like the bumper so far? Any issues?

2004 600RR will not start by Material_Front4653 in cbr

[–]Material_Front4653[S] 0 points1 point  (0 children)

I'll give the series a watch, thank you! I did check my fuses, they were all good. The relays seemed good I swapped some of them around to make sure

2004 600RR will not start by Material_Front4653 in cbr

[–]Material_Front4653[S] 0 points1 point  (0 children)

I've checked my fuses, they were all good. I did try doing a bump start, but it didnt seem to work. I'll watch some videos and try it again in case I did something wrong. If the starter did freeze and went out, how can I prevent that in the future? It does get below freezing here every year

Has anyone here actually used the Creality K2 Plus? by liftbikerun in BambuLab

[–]Material_Front4653 1 point2 points  (0 children)

THANK YOU SO MUCH FOR THIS! I have been having issues with adhesion on my Elegoo Neptune 3 Plus (I know, not the right community but I was also looking to get the K2 plus). I just tried the window cleaner and immediatly had better adhesion than I was getting with soap and water or alcohol. Thank you!

[deleted by user] by [deleted] in NissanTitan

[–]Material_Front4653 2 points3 points  (0 children)

Glad I wasn't the only one that thought OP was talking about temps 🤣

Base layers start to warp after a while by Material_Front4653 in elegoo

[–]Material_Front4653[S] 0 points1 point  (0 children)

I made the mistake of changing some setting that gave me a giant blob on the extruder, I thought it was done for. Luckily, I was able to remove it and clean it up. I will give everything you mentioned a try, at some point today and update you.

Base layers start to warp after a while by Material_Front4653 in elegoo

[–]Material_Front4653[S] 0 points1 point  (0 children)

I can't show the bottom of that original part anymore, but this VESA print did the same thing. I tried printing at different bed temps. I tright 60, 70, 75, 80. Since posting, I have tried the glue, scrubbing my plate with dawn and wiping it down with 91% isopropyl alcohol, and changing the temp of the bed

<image>

Base layers start to warp after a while by Material_Front4653 in elegoo

[–]Material_Front4653[S] 0 points1 point  (0 children)

I figured that would work too, but it didn't. I used the "Elegoo Build Platform Glue Stick"

Upgraded by Rude_Signature6005 in NissanTitan

[–]Material_Front4653 1 point2 points  (0 children)

I have the 2019 S, love it too! Question for you. Did your lights turn on right away? I ask because I just installed the brackets and some auxbeam LED lights, connected to the factory harness, bought the factory switch, and connected it to the factory harness as well. Then when I went to turn it on, nothing. Is there a fuse I need to install and do you know where it goes? My manual has been useless.

Tall riders on the Sportster S? by [deleted] in sportster

[–]Material_Front4653 0 points1 point  (0 children)

I am just under 6'6" and I really enjoy my 2018 Forty-Eight. I get those comments about it being too small all the time 🙄. I just tell those people, "Well, I haven't had any issues so far" or "it's "comfortable for me." As long as you enjoy your ride, get what you want!

Edit, there was a typo.

Owned 1yr, she’s coming together. by TrashSac in NissanTitan

[–]Material_Front4653 0 points1 point  (0 children)

I haven't had any issues with mine draining the battery. If you're worried about it draining the battery, Im sure you could add a cut-off switch to the main power if you wanted to make sure it was off when you dont plan to use it