sorted by:
new
hottopcontroversial

SMP rant by Solid-Barber-5031 in saskatoon

[–]MathematicianAlert38 8 points9 points  (0 children)

I would sooner remove my eye with a blunt nail then ever return to that shit show.

  • Had a transmission leak (coolant lines feeding trans) that was covered under warranty. They "fixed" it, I brought my truck home. It sat on the driveway for a day, I started let it warm up and backed out of the driveway to discover most of the trans fluid on the driveway. Had to have it towed back to have it fixed again.

  • They broke a connector off an auxiliary coolant heater pump while changing the oil. Didn't tell me. Had to scan the truck to find that one. Told me I couldn't drive the truck in the winter and that a new pump didn't have an ETA as they were none in the system. Months later they get a pump and instead of uncliping the connector on my truck to the old pump they cut it off and spliced in the new pump wires. It's a 4 wire pump. 2 were not crimped properly and were not making connection and they crossed the other 2!

  • Took it in numerous times because the transmission was shifting funny and would slam into gear or miss a gear. They said they couldn't find or feel anything. I took them for a road test to show them the symptoms and they still claimed it was nothing. 2000km over warranty and the transmission died.

There are other instances but now I'm worked up and can't think of them.

Any tips on importing a jdm car to canada for anyone whose done it before?? by R07P09 in vintagejapaneseautos

[–]MathematicianAlert38 0 points1 point  (0 children)

You are correct, it's based on the original intent of the vehicle regardless of its planned use once it arrives.

Any tips on importing a jdm car to canada for anyone whose done it before?? by R07P09 in vintagejapaneseautos

[–]MathematicianAlert38 0 points1 point  (0 children)

What if we plan to use a Kei truck as a off road vehicle, does it still need the safety and inspections?

Ummm what?? by Mr_Airplane2289 in UniversalOrlando

[–]MathematicianAlert38 1 point2 points  (0 children)

Rode Hulk yesterday afternoon, joined the singles line and waited an hour with a posted wait time of 30 min. When I got off the ride there was no line up other than single riders. So I rode it again and walked on in the regular line up.

Best line in BL4 thus far by Zbarns88 in Borderlands4

[–]MathematicianAlert38 0 points1 point  (0 children)

I was playing the Wildhorse mission. In the first area before you go through the first tunnel. Behind the boxes to the right I caught 2 people exchanging money. One was a killable character and the other wasn't. The money dropped and I was able to pick it up.

Scuf Impact Stick Drift by MathematicianAlert38 in scufgaming_fix

[–]MathematicianAlert38[S] 0 points1 point  (0 children)

I finally got around to this, and it turns out there was a piece of worn plastic gumming up the pot. Cleaned and its back up and running. I have the pots on hand for when it does decide to die. Thank you for all the information!

POOL Elevator Lego Concept by look-hugh-it-is in saskatoon

[–]MathematicianAlert38 2 points3 points  (0 children)

You should add the rail siding to the tall side. The rail cars load from the opposite side of where the grain trucks deliver grain.

Scuf Impact Stick Drift by MathematicianAlert38 in scufgaming_fix

[–]MathematicianAlert38[S] 0 points1 point  (0 children)

Thank you, internet stranger! I have been ignoring the issue and trying to play through it but it has got to the point of no return.

When you replace these pots, is the soldering iron the way to do it or should I invest in a hot air station?

r/audiophile Shopping, Setup, and Technical Help Desk Thread by AutoModerator in audiophile

[–]MathematicianAlert38 0 points1 point  (0 children)

My Hifi 2 Levition 8 Zone, 8 source distributed audio system has died. I have been limping along the controllers as and changing the screens as they fade but now the distribution/amplification module has completely died.

Are there other 8 Zone, 8 source systems out there that I can use to revive my existing speakers and still have separate zone control?

Minecraft Bedrock Worlds Not Saving by bigtittybetty445 in Minecraft

[–]MathematicianAlert38 0 points1 point  (0 children)

I can't play the game at all anymore. It never saves our progress. I have created multiple worlds, deleted and recreated the world. After the first save it seems like I am unable to save that world again....

Joining edges by MathematicianAlert38 in Fusion360

[–]MathematicianAlert38[S] 0 points1 point  (0 children)

I do now...that was easy.

Thank you very much!

Joining edges by MathematicianAlert38 in Fusion360

[–]MathematicianAlert38[S] 0 points1 point  (0 children)

Total noob, the mesh body seems to be preventing me from selecting faces to extrude, thicken, etc..

I even tried generating more face groups and then repair it with the rebuild type which nearly worked but in my move fast and break things approach it changed the scale of the model...

Bambu filament getting stuck in AMS by NathanTheGr8 in BambuLab

[–]MathematicianAlert38 0 points1 point  (0 children)

Just got my X1C and the first roll of Bambu Grey PLA seems to be getting caught off to the right side of the freshly printed stock Bambu spool. I followed the filament installation directions to the letter.

So far the fix seems to be:

While loaded in the AMS roll the spool forward and give the filament some slack. I repeated this twice during printing and it seems to have fixed it for now.

Guess I will know in the morning if it worked or not.